AC 220V Peel Test Equipment , High Temperature Adhesive Tape Holding Force Tester

Peel Retention Tester High Temperature Adhesive Tape Holding Force Tester

Usage:

Apply to under the continuous heating conditions,Measured parallel to the direction of a certain weight under pressure sensitive adhesive tape adhesive ability.Shear strength (resistance to shear force) is the adhesive tape as the base material used in the same plane when the ability of resistance to static force.

The significance of the application:Shear failure temperature refers to when the sample is load weight, its temperature bonding shear failure of the region.

Overview of the test test method

Solution according to control the speed of a tape is paste in the standard of sheet metal.The steel plate installed in a vertical adjustable heating furnace, and then put a standard quality weight hanging on the free end of the tape.The temperature of the heating furnace to control good speed stability, and determination of shear failure.

Specification:

Temperature control range:Normal~300℃

Control methods:Microcomputer P.L.D automatic temperature control algorithms.

Temperature resolution:0.1℃ unit showing.

Control accuracy:±0.3 ℃.

Heating speed:0.5℃/min

Distribution of precision:±1%(200℃).

Weight:1kg, 9groups.

Electric control: specimen harmlessly, buzzer rang (with switch), and automatically break hot

Manufacturing material: internal SUS# 304 stainless steel plate, external: paint coating.

When counting device: electronic LCD display, automatic retention time, 99999.9 hours (or minute) can be set

Weight and size:80kg 140×55×85 cm

Power:1Ø, AC 220V/50Hz

Test Mehods:

Program set the initial heating furnace temperature of 40 ℃, can preheat furnace to the temperature.

Will spray a solvent on the test panel, absorb good clean materials used to wipe dry.Repeat this solvent cleaning three times.Finally using MEK or acetone to wipe.Test panel before use must maintain at least 10 minutes in this condition.Less than ten minutes of panel should be cleaned.

Samples in the middle of the test at the end of the panel, without any pressure to 24 x 24 mm tape precise coverage area.

In order to prevent the solution volume to cutting on the edge of the test plate samples, need to be at the free end of the sample is placed under another same thickness or slightly thin panel, in the solution volume before contact with the edge of the panel.With 600 + / - 20 mm/min) signals.a detection rate in the extension direction of the area two times.

Put the fixture in the sample free end of the cover, make sure fixture full open on the width of the sample, the uniform load distribution.

Pensile clog, allow 2 minutes to 30 + / - wetting time (stay).

On the test detection device, make the free end of the vertical test samples, make sure there are no stripping force on the samples.

Gently apply load or other agreed load (500 g) on the jig, lest cause sudden impact on tape samples.According to tape the cohesive strength, choose suitable tape load, such as for traditional styrene block copolymer (SBC) pressure sensitive adhesive, selection of load is 500 g, with strong adhesive, such as acrylic pressure sensitive adhesive, selection of load is 1000 g.If the type of adhesive is unknown, the first to use 500 g load.If the tape SAFT is greater than 205 ℃, can increase the applied loads, on the other hand if SAFT is less than 40 ℃, can reduce the applied loads.Applied load as quickly as possible to avoid heat loss, but be careful, don't have sudden impact on tape samples.
Resets the timer.

Close the oven door, start the timer.Note: once the oven door closed, during the test are not allowed to open again.

Company information:

Established in 2003, Dongguan Kejian Instrument Co., Ltd is a high-tech enterprise which professionally research, develop and produce precise testing instruments and provide a full set of testing solution.

Attend the fair:

Our company will attend the world's exhibitions every year and have dealers all over the world.The products sell well in Asia, Europe and America.Welcome to our booth.

GUANGDONG KEJIAN INSTRUMENT CO.,LTD was established in 2003, is a professional research and development the production of hign precision equipment and provide testing solutions for high-tech enterprises. KEJIAN professional technical team and sophisticated production and management level, continues to provide customers with satisfactory products and services, so as to gradually become the industry's leading suppliers of testing machines.

In order to make the customer experience more satisfaction with technical support and service, KEJIAN began to construct a nationwide sales and service network, established the Jiangsu Kunshan branch Office CHANGSHA office ,Chongqing and Xiamen office build sales, technical and after-sales service team, provides more timely, professional support and services for customers.

Follow the market trends of globalization, KEJIAN INSTRUMENT register wholly owned subsidiry- KEJIAN INSDUSTRIAL (HONGKONG）CO.,LTD. started to explore the international market, To provide testing instruments for foreign customers. So far, KEJIAN INSTRUMENT provide quality products and services over 50 national and regional customers, which several customers trust and become a long-term partner with KEJIAN.

Based on the recognition of KEJIAN INSTRUMENT, invited to participate in a number of national standards by the national standards drafting committee drafting and revision process, and has been invited to attend the adhesive industry forum, spare no effort to contribute to national and industry technology development.