Product Details
PSH 2 Layer Low Cost Fast Operation Motor Driven Car Puzzle Parking
System
Product overview
Puzzle parking system is a semi-automatic mechanical stereoscopic
parking equipment. It can be built in the open air or under the
building. It can be divided into whole ground layout, half
underground layout, recolumn layout, etc. PSH puzzle parking system
can be divided into wire rope lifting type, chain lifting type,
hydraulic cylinder lifting type, screw lifting type, combined
lifting type, etc. Multi-layer lifting and transversal parking
garage adopts roller, pulley and steel wire rope for lifting. In
the whole mechanism, there are ac decelerating transversal motor
and lifting motor, steel wire, transversal frame, transversal guide
rail and so on. Its operation principle is to take the upper car,
the lower load plate horizontal move out of the empty parking
space.The lower level of the parking equipment is left and right
transverse, and the top level is up and down.
Characteristics
- This parking equipment is simple in structure, convenient in
operation, easy to maintain and repair.
- Short construction cycle, low construction cost, strong
adaptability to the site, low requirements for civil construction,
can be built in the open air, can also be built in the underground
of the building, the scale can be large or small, according to
different terrain and space for any combination, arrangement, high
space utilization rate, safe and reliable equipment, fast access
car.
- When it is working, there should be exchange parking space, that
is, empty parking space.Therefore, the calculation of the effective
parking number is not a simple superposition of the number of
parking Spaces on the ground and the number of floors.Usually the
larger garage is divided into a number of units, a unit can only be
stored and taken by one person first or later, not two or more
people at the same time.Therefore, if the unit is divided too
large, it will reduce the efficiency of storing and taking cars;Too
small a division will reduce the number of parking spaces and
reduce the use of land.Based on experience, a unit responsible for
5 to 16 cars is appropriate.
- The lifting and horizontal mechanical parking equipment has the
following safety devices: emergency stop switch, prevent
overrunning device, vehicle length, width, height limit device,
vehicle blocking device, vehicle error detection device, vehicle
position detection device on the vehicle board, prevent vehicle
board falling device and warning device, etc.
What is the dimension of semi-automated parking system
The height of the entrance and exit of the semi-automatic
mechanical parking equipment should be no less than 1700 mm. The
height of the passage for people inside the parking equipment
should be no less than 1700 mm. The width of the passage should be
increased by more than 500 mm on the basis of suitable parking
vehicle width.
Generally, there are 2 layers,3 layers,4 layers,5 layers,6 layers,7
layers,8 layers and other types.
Technical Parameters
Item | Parameters |
Drive Mode | motor drive |
Levels of system | 2 |
Size of car (L*W*H) | 5000*1850*1550mm 5000*1850*2050mm |
Car Weight | 2000kg |
Operation Mode | Auto IC card/ Manual button |
Lifting motor power | 4KW |
Lifting speed | 8-12M/MIN |
Sliding motor power | 0.2KW |
Sliding speed | 8M/MIN |
Control Method | Touch screen / Push button or IC card |
Parking way | Forward in, Back out |
Electricity | 3 phases 5 wires, 380V, 50HZ |
Safety devices | Over-length, over-width, over height detection; car space with car
or without car detection; wrong entrance detection, |
Malfunction indication | Computer malfunction diagnosis, human-computer communication
information display |
Parts appearance treatment | Hot spray galvanized treatment and high-grade anti-corrosion
painting |
Controller | PLC, with control monitoring, IC card, manual and operative panel; |
Company Profile
Shanghai Changyue Automation Machinery Co., Ltd, an established Factory in Jiangsu,China, with state of the art
facility to design, manufacture and install world-class solutions
for automated and mechanical car parking systems offered to our
customers worldwide.
We enjoy excellent experience packed with strong technical know-how
using latest manufacturing machines such as CNC Plasma, Press
Brake, Shearing Machine, Laser Cutting and Welding to guarantee the
quality of every single part with minimal error and meeting
international manufacturing standards in all production stages.
ChangYue's Research and Development team is committed to provide unmatched
quality yet maintaining efficient & ergonomic operation to
insure producing durable and competitive parking lifts, service
lifts for commercial and residential solutions.
Units are designed according to EN 60204-1: 2018, EN ISO
12100:2010, EN 14010: 2003+A1:2009 standards and products certified
according to machinery directive 2006/42/EC.