Z15 Z18 H Beam Assembly Machine Manual Automatic Spot Welding Machine

Automatic Spot Welder Or Manual H Beam Assembly Machine Z15 Z18 Z20

Web height: 160-1500/1800/2000mm
Web thickness: 3-40
Flange width: 160-800mm
Flange thickness: 6-40mm
Workpiece length: 4000-20000mm
Assembly spped: 0.5-6 m/min
Electrical assembly: the brand is AC converter
Total power: 10KW
Power supply: AC 380V 50HZ 3phsaes

Suitable workpiece`s size:

Web clamping device:Two groups of web plate fastening device for synchronous movement, through the coupling and the shaft connection between two groups.Total power of the motor drive gear reducer, and then through a screw transmission so that the web clamp sliding seat together to walk in the middle.Web clamping mechanism of two side by clamping bolt tightening on the sliding seat directly, through the shaft linkage with open or shrink, to meet the requirements of the web the clamping, realized the machine automatically.

Wing clamp device:Two sets of wings clamp lock mechanism for synchronous movement, through the coupling and the shaft connection between two groups.Total power of the motor drive gear reducer, and then through a screw transmission so that the web clamp sliding seat together to walk in the middle.Wing clamp on two sides of the clamping seat directly to tighten bolts on the sliding seat through the shaft linkage with open or shrink, to meet the requirements of wing plate clamp, realized the machine automatically.

The door frame press device:Can lift the main pressure beam mainly include:Pressure cylinder, lift drag plate, eccentric adjustment wheel, pinch roller.Hydraulic alignment equipment,hbeam not spot welding, flange and web will produce uneven phenomenon, then we can align the wing, to web hbeam equipment parts, makes the plate close to the base plate, so that the transverse alignment.Alignment device can make mechanical flip up and down.

(2)the pull rodof the system:On the bar system mainly includes:Pull rod box, rod oil cylinder, pull rod.When not set of wing, web transmission into the machine, the wings, not in the required position precision, web and web need support at this time.Rod for the system is able to wing, web preliminary positioning and its process are respectively, by the surface tension in the oil cylinder and the web of the tensioning oil cylinder control.Pull rod box by pull rod connected between each other.

(3)Input roller:Input of raceway is mainly with the input process of hbeam, it consists of, passive and active raceway groove, the arrangement and the spacing between rolling suitcase.

(4)Output roller:Output of raceway is mainly with the output process of hbeam, it consists of, passive and active raceway groove
(5)Hydraulic system assembly:Hydraulic system mainly includes:Hydraulic pump station, the main pressure cylinder, wing plate positioning cylinder, web positioning cylinder, wing powder tight oil cylinder (3pcs), web clamping cylinder (2pcs), rubber hose, oil pipe, seamless steel pipe.

Due to the limitation of the website, I can only offer you a pic and a littel detailed information, so if you are interested in the products , or want more detailed information or have some problems, please contact me freely.I will try to solve it for you as soon as possible.

​​

​​

Z15 H beam assembly machine
Structure Principle
This machine is mainly composed of the following parts:​

a)the main drive roller
b) web clamping system
c) wing plate clamping system
d) main lifting compaction beam
e) H steel partially aligned

Rod on the system (two groups)

Input and output rollers

Hydraulic system assembly

Scope of supply and composition

-the main engine assembly, web clamp, flange plate clamping, etc..
B.input and output roller assembly:
-roller of 2.6m/ * 6 festival festival, rod system etc.
C.hydraulic system:
-pump station, oil motor, high pressure hose, hydraulic cylinder, etc..
D. automatic spot welding system:
-350A CO2 welding power source*2pcs.welding, mechanical tracking mechanism, the hydraulic cylinder clamping mechanism etc. (manual welding without the equipment, automatic welding).
E.electric control system:
-electric cabinet, AC inverter, etc..
F.spare parts:
-O button 3. The HH54PDC24V relay 2. The molten core 4A, each 3 6A.

Technical documents
Instructions for the use of the complete machine (including the electrical principle diagram, hydraulic principle diagram, wearing parts list, etc.)
Frequency converter using manual, hydraulic pump station manual
Delivery list
Equipment qualification certificate
Basic graph

Production and self owned part
A. Foundation (provided by the supplier).
B. anchor bolts and expansion bolt.
C. machine foundation.