AT89S8253-24AU MCU 8-bit 8051 CISC 12KB Flash 3.3V/5V 44-Pin TQFP

MICROCHIP AT89S8253-24AU MCU 8-bit 8051 CISC 12KB Flash 3.3V/5V 44-Pin TQFP

About Microchip Technology

Microchip Technology is a leading provider of microcontroller and analog semiconductors, providing low-risk product development, lower total system cost and faster time to market for thousands of diverse customer applications worldwide. Headquartered in Chandler, Arizona, Microchip offers outstanding technical support along with dependable delivery and quality.

More related products :

Related Overview:

The ATtiny2313 is a low-power CMOS 8-bit microcontroller based on the AVR enhanced RISC architecture.

By executing powerful instructions in a single clock cycle, the ATtiny2313 achieves throughputs approaching

1 MIPS per MHz allowing the system designer to optimize power consumption versus processing speed.

The AVR core combines a rich instruction set with 32 general purpose working registers. All the 32 registers are directly connected to the Arithmetic Logic Unit (ALU), allowing two independent registers to be accessed in one single instruction executed in one clock cycle.

The resulting architecture is more code efficient while achieving throughputs up to ten times faster than conventional CISC microcontrollers.

The ATtiny2313 provides the following features: 2K bytes of In-System Programmable Flash, 128 bytes EEPROM, 128 bytes SRAM, 18 general purpose I/O lines, 32 general purpose working registers, a single-wire Interface for On-chip Debugging, two flexible Timer/Counters with compare modes, internal and external interrupts, a serial programmable USART, Universal Serial Interface with Start Condition Detector, a programmable Watchdog Timer with internal Oscillator, and three software selectable power saving modes. The Idle mode stops the CPU while allowing the SRAM, Timer/Counters, and interrupt system to continue functioning. The Power-down mode saves the register contents but freezes the Oscillator, disabling all other chip functions until the next interrupt or hardware reset. In Standby mode, the crystal/resonator Oscillator is running while the rest of the device is sleeping. This allows very fast start-up combined with low-power consumption. The device is manufactured using Atmel’s high density non-volatile memory technology. The On-chip ISP Flash allows the program memory to be reprogrammed In-System through an SPI serial interface, or by a conventional non-volatile memory programmer. By combining an 8-bit RISC CPU with In-System Self-Programmable Flash on a monolithic chip, the Atmel ATtiny2313 is a powerful microcontroller that provides a highly flexible and cost effective solution to many embedded control applications. The ATtiny2313 AVR is supported with a full suite of program and system development tools including: C Compilers, Macro Assemblers, Program Debugger/Simulators, In-Circuit Emulators, and Evaluation kits.

Features:
• Utilizes the AVR® RISC Architecture
• AVR – High-performance and Low-power RISC Architecture
– 120 Powerful Instructions – Most Single Clock Cycle Execution
– 32 x 8 General Purpose Working Registers
– Fully Static Operation
– Up to 20 MIPS Throughput at 20 MHz
• Data and Non-volatile Program and Data Memories
– 2K Bytes of In-System Self Programmable Flash
Endurance 10,000 Write/Erase Cycles
– 128 Bytes In-System Programmable EEPROM
Endurance: 100,000 Write/Erase Cycles
– 128 Bytes Internal SRAM
– Programming Lock for Flash Program and EEPROM Data Security
• Peripheral Features
– One 8-bit Timer/Counter with Separate Prescaler and Compare Mode
– One 16-bit Timer/Counter with Separate Prescaler, Compare and Capture Modes
– Four PWM Channels
– On-chip Analog Comparator
– Programmable Watchdog Timer with On-chip Oscillator
– USI – Universal Serial Interface
– Full Duplex USART
• Special Microcontroller Features
– debugWIRE On-chip Debugging
– In-System Programmable via SPI Port
– External and Internal Interrupt Sources
– Low-power Idle, Power-down, and Standby Modes
– Enhanced Power-on Reset Circuit
– Programmable Brown-out Detection Circuit
– Internal Calibrated Oscillator
• I/O and Packages
– 18 Programmable I/O Lines
– 20-pin PDIP, 20-pin SOIC, 20-pad QFN/MLF
• Operating Voltages
– 1.8 – 5.5V (ATtiny2313V)
– 2.7 – 5.5V (ATtiny2313)
• Speed Grades
– ATtiny2313V: 0 – 4 MHz @ 1.8 - 5.5V, 0 – 10 MHz @ 2.7 – 5.5V
– ATtiny2313: 0 – 10 MHz @ 2.7 - 5.5V, 0 – 20 MHz @ 4.5 – 5.5V
• Typical Power Consumption
– Active Mode
1 MHz, 1.8V: 230 µA
32 kHz, 1.8V: 20 µA (including oscillator)
– Power-down Mode
< 0.1 µA at 1.8V

More Similar Part Number:

Environmental & Export Classifications

Angel Technology Electronics Co Was Founded In HongKong Since 2006, Our branch Located In The Silicon Valley Of China, Shenzhen.Angel Technology provide one stop service for electronic components,PCB and PCB Assembly(SMT).

The Mission Of Angel Technology Electronics Co has always been to provide Quality Electronics Components To Manufacturers Worldwide.Angel-tech's vision is become the excellent electronic components supplier with the highest satisfaction between employees and customers. Early On We became the Primary channel for project closures And Inventory build-ups for Major Distributors such as Arrow Electronics and Contract Manufacturers. Angel Technology Electronics Co Has since then added Sourcing Of High Quality Components From Local Manufacturers In China.

The corporate Philosophy Policy of Angel Technology Electronics Co is Innovation,Not limited by the inhereent thinking,always looking for new ways to meet the needs of the market.So We have specialized in providing customers with one-stop service of electronic components, PCB and SMT since 2006, helping end customers to efficiently complete the full project including BOM list procurement process etc.

Angel Technology Electronics Co Has always been Customer Driven Rather than Opportunity Driven. Meaning- Angel Tech Will Always Choose Path That is the best For Long Term Relationship With Customer Over Short Term View. It Is Why We Have One Of The Highest Customer Retention Scores Of China Based Distributors.

Prioritizes client satisfaction:

Because of our clients are at the heart of how we work,At Angel Technology Electronic Co, our goal is to provide customers with electronic components supply,PCB production, SMT assembly one-stop service.

IInnovation and creativity:
We believe that innovation is fundamental to our success and we take particular pride in regularly working closely with industry innovators and our clients to set new standards. In recent years, Angel Technology Electronics co have also started collaborating with more and more corporations to explore new technologies in smart home and PMIC.

Inventory management:
Angel Technology Electronics co provides a third-party warehousing and professional IT inventory management software for customers to achieve seamless docking. The ownership of parts can only be transferred when the customer uses parts.

Angel Technology Electronic's incoming parts have undergone rigorous inspection, and the products are stored in standard anti-static, anti-humidity, anti-high temperature, and the stock are regularly tested to make the parts safe.

Packaging transportation standard :
The parts are tested for performance during shipment, and the packaging must be waterproof, moisture-proof and shock-proof. At the same time, Angel Technology Electronics cooperates with a number of international first-class freight companies to ensure that the parts of first- and second-tier cities can be delivered at that day, and arrive the next day. The goods of third-tier cities and remote areas can be delivered at that day and arrive within two days to ensure that customer.

Angel Technology Electronics Co have been passionated about electronic components distribute and integrated solution provider since 2006. We are also a PCBA manufacturer with our own manufacotry who can better serve for customers of smart home, communication, industry, automotive electronics and medical electronics etc.