IEC 62196 5000N Ev Charger Tester Connector Plug Car Drive Over Test Equipment

Brand Name:Sinuo

Certification:Calibration Certificate (Cost Additional)

Model Number:SNQC1010

Minimum Order Quantity:1

Delivery Time:30 days

Payment Terms:T/T

Contact Now

Add to Cart

Sinuo Testing Equipment Co. , Limited

Verified Supplier

Location: Guangzhou Guangdong China

Address: Room 101, 1st Floor, No. 6, Third Street, Pingshan Industrial Zone, Shibi Street, Panyu District, Guangzhou, China

Supplier`s last login times: within 28 hours

View Contact Details

Shipping

lt's easy to get a shipping quote! Just click the button below and complete the short form.

Get Shipping Quote

Product Details Company Profile

Product Details

IEC 62196 New Energy Vehicle Charging Connector Plug Drive Over Test Equipment

Complied Standards & Clauses

IEC 62196-1Ed.4 CDV 2020 “Plug, socket-outlets, vehicle connectors and vehicle inlets–Conductive charging of electric vehicle-Part1: General requirements” clause 33.2 and 33.3.

Equipment Overview

Samples and Restrictions: Accessories (such as plugs or vehicle connectors) wired with the minimum size cable of a type recommended by the manufacturer.

Application: It is used to check whether a plug or vehicle connector shall have adequate resistance to damage from being driven over by a vehicle, unless it is provided with a cable management system which prevents the accessory from being left on the ground.

Technical Parameters

Standards & Clauses	IEC62196-1: 2014 clause 33.2 and 33.3
Test Station	Single
Electrical Control Method	PLC intelligent integrated control, color humanized touch interface operation
Drive Mode	Motor driven
Load Carrying	A. Crushing force (5000±250) N B. Crushing force (11000±550) N
Drive Over Speed	(8±2) km/h for (5000±250) N test 0~5 km/h can be set for (11000±550) N test
Roll Over Method	The linear motor module is used to drive the automotive tire to simulate the front and rear reciprocating rolling motion (to simulate the damage caused by the accidental rolling to the vehicle connector or plug during the forward or reverse moving of the car in the real scene)
Crushing Force Loading	Using supplementary weights to apply the crushing force
Drive Over Tire	ST225 / 75R15 2 pcs, one for (5000±250) N test, the other for (11000±550) N test
Air Pressure of Tire	(2.2±0.1) bar
Test Floor	A bottom plate with cement/ concrete surface
Lifting Device	Electric hoist
Tire Installation	Electric hoist lifting and restructuring
Driveover Speed	Can be display and set on the touch screen
Shock Absorption Method	Damping spring
Test Principle	Accessories wired with the minimum size cable of a type recommended by the manufacturer shall be placed on a concrete floor in any normal position of rest. A crushing force of (5000±250) N or (11000±550) N shall be applied by a conventional automotive tire, P225/75R15 or an equivalent tire suitable for the load, mounted on a steel rim and inflated to a pressure of (2.2±0.1) bar. The wheel is to be rolled over the vehicle connector or plug at a speed of (8±2) km/h. The accessory is to be oriented in a natural resting position before applying the force in a different direction for each sample. The accessory under test shall be held or blocked in a fixed position so that it does not move substantially during the application of the applied force. In no case is the force to be applied to the projecting pins.
Structure	A. The equipment chassis is treated with a protective cover to ensure the safety of the test process; the bottom of the chassis is equipped with a shock-absorbing foot pad and a pulley structure, which is easy to install and disassemble. The rolling test is guided by heavy-duty guide rails, sliding rollers, high-power servo motors combined with turbo reducers to drive the main shaft to achieve the test speed. The sample fixing and sliding device is equipped with a function box mounting fixture, and the fixture is universally adjustable (up and down, left and right can be adjusted according to the size and shape of the sample). B. The crushing force adjustment device is designed as an up and down adjustable structure. The tested tire, upper and lower frame, power system, and counterweight are the test weights required as a whole, and are equipped with imported precision force sensors; fine-tune each applied force, adjust the force after the tire contacts the sample, and the force will automatically return to zero, and the force value will be displayed again; The force accuracy of each test is guaranteed. C. The equipment adopts the working method of tire front and rear driving (rolling direction is driven by servo motor forward and reverse), keeping the sample fixed, and realizing the most realistic simulation of tire rolling reciprocatingly, thus effectively simulating the crushing of the sample. D. The control system is an independent body. The host is composed of PLC control, touch screen, casters and connecting lines, which is convenient for mobile connection.

Questions & Answers

Q : What is the force test range?
A :Our system can test two kinds of force, one for (5000±250) N test, the other for (11000±550) N test, just reflects the difference between a car and a big truck.

Q : What are the features of this system?
A : The whole system weighs up to 3 tons. The material structure is stable and the plate is thick. In addition, our design can actually simulate the forward movement of tires at the speed of 8km/h in the test area, which makes the test more accurate.

Company Profile

Sinuo Testing Equipment Co., Limited established in 2019, but Sinuo has rich experience in manufacturing test euipment, test system and offering overall laboratory construction of electronic and electrical products. Sinuo's main products include electrical vehicle test equipment, battery testing equipment, electromagnetic compatibility (EMC) test system, environmental testing equipment, fire retardant test equipment, dust-proof waterproof testing equipment and electrical appliances testing equipment. Our products covering electrical vehicle, electric power, communication, electrical appliances and electronic devices industries.

Sinuo has a professional technical research and development team, which is proficient in various international standards such AS IEC, ISO, EN, VDE, BS, AS, ASTM, GB and industry standards such AS MBN LV124, VW-80000. We master physical mechanics, heat, electricity, fluid and other theoretical knowledge in the application of equipment. And continue to focus on industry standard equipment performance optimization, operation simplification and equipment stability and reliability improvement.

Sinuo has two factories in Guangzhou and Dongguan, and cooperates with many research institutions and schools. Our R&D and production capacity are in the forefront. We have authorized agents in South Korea, the United States, South Africa, Egypt, Pakistan, the Philippines and other places, we serve customers BV, CSA, Intertek, SGS, TUV and other internationally renowned testing and certification institutions, local government quality inspection departments and production factories.