1m3 EV Connector Testing Equipment PLC Control Sand And Dust Test Chamber
Brand Name:Sinuo
Certification:Calibration Certificate (Cost Additional)
Model Number:SN441
Minimum Order Quantity:1
Delivery Time:30 days
Payment Terms:T/T
Contact Now
Add to Cart
Verified Supplier
Location:
Guangzhou Guangdong China
Address:
Room 101, 1st Floor, No. 6, Third Street, Pingshan Industrial Zone, Shibi Street, Panyu District, Guangzhou, China
Supplier`s last login times:
within 28 hours
Product Details
Company Profile
Product Details
IEC 62196 Electric Vehicle Sand And Dust Test Chamber
Complied Standards & Clauses
IEC 62196-1Ed.4CDV 2020 clause 20.2
IEC60529 Fig 2
IEC 60884-1:2013 clause 16.2
IEC60598-1-2008
IEC60335-1 Clause 22.1
Equipment Overview
The test device is suitable for sealing parts and enclosure’s sand and dust resistance capacity testing of the electrical and electronic products, car and motorcycles spare parts and seals. In order to detect the use, storage, transport performance of the electrical and electronic products, car and motorcycles spare parts and seals under the sand and dust environment.
The test equipment uses intelligent and humanized PLC control system, the inner of the test equipment is made of high quality SUS304 stainless steel, the enclosure is A3 plate electrostatic spraying. And it also has large observation window and manual wiper device. The security protection is good.
The sand and dust test chamber is designed and manufactured according to IEC60529 Fig 2, IEC 60884-1:2013 clause 16.2, IEC60598-1-2008, IEC60335-1 Clause 22.1, IEC 62196-1Ed.4CDV 2020 clause 20.2, and etc.
Configuration
| Device Name | Dust and Sand Test Chamber | ||
Main configuration | Cabinet | Enclosure material | A3 plate electrostatic spraying |
| Inner material | SUS304B Stainless steel | ||
| Lead hole | The sample can be external power supply through this hole | ||
| Observation window | large observation window in the middle of the door | ||
| Electrical control system | Controller | PLC Control: A. blowing dust time (stop, blowing) can be adjusted B. Cycle: arbitrary adjustable C. Preset test time: 0.1H-9999.9H arbitrary adjustable D. Power: On-off- On E. There are accumulating function and power-off protection function | |
| Vacuum system | Equipped with a vacuum pump, pressure gauge, air filter, pressure regulator, connecting pipe | ||
Security Protection Device | Power overload, short-circuit protection | ||
| Ground Protection | |||
| Voltage Protection | |||
| Motor phase loss protection | |||
| Alarm beep prompt | |||
Technical Parameter
| Model | SN441-1000L | |
| Working size(mm) | L1000*W1000*H1000 | |
| Outer size (mm) | L1500*W1400*H1900 | |
| Power supply | Three phase AC 380V, 50Hz | |
| Main technical parameters | Temperature range | Room temperature |
| Test dust | dry talc which can go through the sieve of 75μm and the square sieve of wire diameter 50μm. | |
| Test sand (or talc) dosage | 2kg/m³ | |
| Vacuum pump | 0~30Kpa | |
| Air pressure | 0.5~1.0Mpa | |
Sample rack height adjustment range | 0~750MM | |
Timing range | 0~99 hours 59 min | |
Timing accuracy | ±1min | |
Load cycle control | 0~99 hours 59 min | |
Ash blowing cycle control | 1s~9999 min | |
| Sand and dust concentration | 2～4kg/m3 | |
| Air flow speed | ≤2m/s | |
Details:
1m3 EV Connector Testing Equipment PLC Control Sand And Dust Test Chamber
Inquiry Cart
0