MX25R3235FZNIL0 MXIC ULTRA LOW POWER (SERIAL MULTI I/O) FLASH MEMORY Program Suspend/Resume & Erase Suspend/Resume

MX25R3235FZNIL0 MXIC ULTRA LOW POWER (SERIAL MULTI I/O) FLASH MEMORY Program Suspend/Resume & Erase Suspend/Resume

1.Key Features
• Ultra Low Power Mode and High Performance Mode
• Wide Range VCC 1.65V-3.6Vfor Read, Erase and Program Operations
• Unique ID and Secure OTP Support
• Multi I/O Support - Single I/O, Dual I/O and Quad I/O
• Program Suspend/Resume & Erase Suspend/Resume

2.FEATURES

Supports Serial Peripheral Interface -- Mode 0 and Mode 3
• 33,554,432 x 1 bit structureor 16,777,216 x 2 bits (two I/O mode) structure or 8,388,608 x 4 bits (four I/O mode) structure
• Equal Sectors with 4K byte each, Equal Blocks with 32K byte each, or Equal Blocks with 64K byte each - Any Block can be erased individually
• Single Power Supply Operation- Operation Voltage: 1.65V-3.6V for Read, Erase, and Program Operations
• Latch-up protected to 100mA from -1V to Vcc +1V

3.PERFORMANCE
• High Performance- Fast read
- 1 I/O: 80MHz with 8 dummy cycles
- 2 I/O: 80MHz with 4 dummy cycles, equivalent to 160MHz
- 4 I/O: 80MHz with 2+4 dummy cycles, equivalent to 320MHz
- Fast program and erase time- 8/16/32/64 byte Wrap-Around Burst Read Mode
• Ultra Low Power Consumption
• Minimum 100,000 erase/program cycles
• 20 years data retention

4.SOFTWARE FEATURES
• Input Data Format
- 1-byte Command code
• Advanced Security Features
- Block lock protectionThe BP0-BP3 status bit defines the size of the area to be software protection against program and erase instructions
• Additional 8K bits secured OTP
- Features unique identifier.
- Factory locked identifiable and customer lockable
• Auto Erase and Auto Program Algorithm
- Automatically erases and verifies data at selected sector or block
- Automatically programs and verifies data at selected page by an internal algorithm that automatically times the program pulse widths (Any page to be programed should have page in the erased state first)
• Status Register Feature
• Command Reset
• Program/Erase Suspend and Program/Erase Resume
• Electronic Identification
- JEDEC 1-byte manufacturer ID and 2-byte device ID
- RES command for 1-byte Device ID
- REMS command for 1-byte manufacturer ID and 1-byte device ID
• Support Serial Flash Discoverable Parameters (SFDP) mode
• Support Unique ID (Please contact local Macronix sales for detail information)

5.HARDWARE FEATURES
• SCLK Input
- Serial clock input
• SI/SIO0
- Serial Data Input or Serial Data Input/Output for 2 x I/O read mode and 4 x I/O read mode
• SO/SIO1
- Serial Data Output or Serial Data Input/Output for 2 x I/O read mode and 4 x I/O read mode
• WP#/SIO2
- Hardware write protection or serial data Input/Output for 4 x I/O read mode
• RESET#/SIO3 * or HOLD#/SIO3 *
- Hardware Reset pin or Serial input & Output for 4 x I/O read mode or
- HOLD feature, to pause the device without deselecting the device or Serial input & Output for 4 x I/O read mode * Depends on part number options
• PACKAGE
- 8-pin SOP (150mil/200mil)
- 8-land WSON (6x5mm)
- 8-land USON (4x3mm)
- 12-ball WLCSP (3-2-3 Ball Array)
- All devices are RoHS Compliant and Halogen-free

6.GENERAL DESCRIPTION
MX25R3235F is 32Mb bits Serial NOR Flash memory, which is configured as 4,194,304 x 8 internally. When it is in four I/O mode, the structure becomes 8,388,608 bits x 4 or 16,777,216 bits x 2. MX25R3235F feature a serial peripheral interface and software protocol allowing operation on a simple 3-wire bus while it is in single I/O mode. The three bus signals are a clock input (SCLK), a serial data input (SI), and a serial data output (SO). Serial access to the device is enabled by CS# input.
When it is in two I/O read mode, the SI pin and SO pin become SIO0 pin and SIO1 pin for address/dummy bits input and data output. When it is in four I/O read mode, the SI pin, SO pin, WP# pin and RESET#/HOLD# pin become SIO0 pin, SIO1 pin, SIO2 pin and SIO3 pin for address/dummy bits input and data output.
The MX25R3235F MXSMIO® (Serial Multi I/O) provides sequential read operation on whole chip.
After program/erase command is issued, auto program/erase algorithms which program/erase and verify the specified page or sector/block locations will be executed. Program command is executed on byte basis, or page (256 bytes) basis, or word basis for erase command is executed on sector (4K-byte), or 32KB block (32K-byte), or block (64K-byte), or whole chip basis.
To provide user with ease of interface, a status register is included to indicate the status of the chip. The status read command can be issued to detect completion status of a program or erase operation via WIP bit.Advanced security features enhance the protection and security functions, please see security features section for more details.
The MX25R3235F utilizes Macronix's proprietary memory cell, which reliably stores memory contents even after 100,000 program and erase cycles

Shenzhen Hongxinwei Technology Co., Ltd is located in the Bao’an District of Shenzhen.It is a high-tech enterprise setting research and development, production, sales into an integration. The company covers an area of 15 acres, having modern producing workshop and professional production and testing equipments. The company has an existing staff of more than 100 people.The company has set up offices in Shenzhen, Hongkong and Singapore providing worldwide service.