827+H2000 Kits

Item Description

Here we are offering a Gravity Feed Production HVLP(High Volume Low Pressure)Spray Gun complete kit. This kit includes 2 Professional Spray Guns, one Air Regulator with Gauge.one in-line Air Drier (Water/Oil Separator) and other accessories. This kit also comes with a durable all in one carrying case for very convenient mobility.

HVLP Spray Gun supplies low pressure through the air cap which makes the spraying softer, easily controlled and less overspray in high transfer efficiency.

Features:

Full Size Spray Gun:

Designed to provide equal atomization and partical size.
Stainless steel needle and nozzle accommodate a variety of coatings.
Light weight, ergonomic design and easy trigger pivot reduces operating fatigue.
Precise 1.4mm stainless steel needle and nozzle set.
3 Knobs for full adjustment: Fluid, Pattern and Air Pressure Controls.
600ML Non-drip Nylon Fluid Cup with Lid.
Comes with a True Micrometer Air Regulator with Gauge as free gift.
Operating Pressure: 30-80 PSI
Air Consumption: 14 CFM
Compressor Required: 1-3 HP
Air Inlet Diameter: 1/4"
Mini Size Spray Gun:

Used for tight areas, small jobs and touch up.
Precise 1.0mm stainless steel needle and nozzle set.
3 Knobs for full adjustment: Fluid, Pattern and Air Pressure Controls.
250ML Non-drip Plastic Fluid Cup with Lid.
Operating Pressure: 30-80 PSI
Air Consumption: 2.8 CFM
Compressor Required: 1-3 HP
Air Inlet Diameter: 1/4"

Package Includes:

1x Full Size HVLP Spray Gun with 1.4mm Fluid Tip
1x Mini Size HVLP Spray Gun with 1.0mm Fluid Tip
1x 600ml Nylon Cup with Lid
1x 250ml Plastic Cup with Lid
1x True Micrometer Air Regulator with Gauge
1x In-line Air Drier (Water/Oil Separator)
2x Spanner Wrenches
1x Hex Wrench
1x Screw set
1x Brush Cleaning Kit
2x Cup Filters
2x Instruction Manual (General for some models)

How to Select a Spray Gun Nozzle Tip Size

What Size Spray Tip Should I Use with my Spray Gun?

There are many different things to consider when selecting the appropriate size spray tip for each job. The amount of information on the subject can be overwhelming, so we at the Bottom Paint Store have done our best to make this step easier for you.

There are three main factors to consider when determining the size tip that will produce the best results.

• First, examine the coating that will be sprayed. Put simply, heavier coatings will require a larger orifice size than lighter ones. For example, primers are usually thicker than the accompanying paint so you should use a 1.7 or 1.8 mm tip to prime most surfaces. Most painters will stay in the range of 1.2 to 2.0 mm unless the paint being applied is specialized. (See chart below.)
• The next thing to consider is your project surface area. This determines the appropriate fan width that your sprayer will produce, that is, the shape in which the product will leave the gun nozzle. Airless spray guns have more control over the fan width than conventional spray guns because the coating is forced through the tip without being atomized by air. This causes the tip to have a large impact on the fan width and shape. Most boat projects consist of large surfaces and so a wide fan will increase the spray coverage and also provide the ability to spray close to the surface without too much build up. Smaller surfaces will require a small fan width to reduce overspray. This also makes it possible to spray further away from the surface without too much falloff because the fan is more focused.
• Lastly, consider the spray gun that is being used. Make sure that the spray tip you plan on using will be supported by the gun. Most spray gun manufacturers will provide this information in their product overview.

• Common Spray Tip Sizes and Their Uses
  Tip size (mm)	Commonly Used for
  0.8	Parting Films – PVA – very fine mist
  1.2	Clear Coats – super fine finishes
  1.4	All Around Tip – clears, base coat, single stage paints
  1.6	General Purpose – light to heavy viscosity materials
  1.8	Primers – will apply primer quickly
  2.2 -2.5	Gel Coats and Resins – for thick resins and not paints

Ningo Seelion Co.,ltd is an OEM manufacturer and a trader with more than 10 years trading experiences which located in Ningbo ,Zhejiang,China.

Seelion has developed a comprehensive range of products to meet clients' various requirements on air painting gun, washing gun, blowing gun, inflating gun, greasing gun, gauge tool, air tools kit etc.

At present, we have lots of excellent manufactures , which factories possess hundres of numerical lathes, dozens of CNC auto drilling machines, integrated assemble lines and auto-packing lines. Together with our excellent facory partners, we are now capable of producing about 5,000 guns daily to meet your requirements.

Our products are exported to many countries in the world such as North America, European Union, South-East, Asia, Africa and the Middle East.
Based on the high-efficiency management, advanced-tech equipments and professional workers, we have thus built the confidence of meeting the fierce competition ahead of us, with vision to be one of the leading partners worldwide through our continuous creativity and cooperation in providing high quality products and service persistently.

In addition, the approval of UL, GS, CE and ISO9001 quality management system further ensure the stability and consistence of our products.We warmly welcome customers from all over the world to have
visits or business cooperation with us!