Product Details
Corrugated Rubber Cleat Sidewall Belt Conveyor 30-90 Degree Slop
With OEM Service
General
This Sidewall belt conveyor with corrugated shield, in particular
applied in conveying material in big inclination, for it with
corrugated shield and horizontal clapboard belt. And it can widely
used in coal, metallurgy, chemical industry, light industry,
petroleum, port, mechanical etc to convey all kinds of bulk
materials and the piece.
Density of handled bulk materials 500~2500kg/m3, max inclination is
90°, max lump size is 550mm, lump of handled should depends on belt
width, belt speed, clapboard height and inclination.
Ambient temperature generally -25~+40℃, material temperature to be
handled should be under 50℃. It should take other measures for
special requirement such as heat resistant, proof cold, resistant
retard, resistant acid and alkali, resistant abrasion, proof
explosion, proof water etc.
Advantages And Features
- Widely used, can transfer all kinds of bulk material in different
angles and directions.
- No transfer points- the belt are capable of turning at any angle
right from feed hopper to discharge point
- No spillage at the steep angle when transfer bulk material.
Maximum utilization of space – able to convey material at angles up
to 90 degree, able to instead of bucket elevator.
Low power requirement, low cost, long service life and quiet smooth
running.
Technical parameters for reference
Remarks: the below capacity is based on coal and speed 1m/s to
caculated for reference.
Bandwidth | 500mm |
Cleats hight | 160mm | 200mm | 240mm |
Pitch of cleats | 126mm | 376mm | 252mm | 378mm | 504mm | 252mm | 378mm | 504mm |
Slop | 30 degree | 186 t/h | 129 t/h | - | 207 t/h | 159 t/h | - | 283 t/h | 229 t/h |
40 degree | 150 t/h | 99 t/h | - | 160 t/h | 122 t/h | - | 231 t/h | 176 t/h |
50 degree | 120 t/h | 79 t/h | 79 t/h | 112 t/h | - | - | 185 t/h | 141 t/h |
60 degree | 98 t/h | 64 t/h | 64 t/h | 105 t/h | - | 229 t/h | 151 t/h | - |
70 degree | 80 t/h | 52 t/h | 52 t/h | 85 t/h | - | 287 t/h | 123 t/h | - |
90 degree | 49 t/h | - | - | 52 t/h | - | 115 t/h | 76 t/h | - |
Selection Conditions
- Material to be processed: _____
- Max. granule size of the feeding material: _____mm
- Handling capacity (Ps. It means the total material capacity feeding
from the inlet): _____t/h
- Percentage of Max. granule in material:_________%
- Upstream equipment (Ps. It means what kind of Equipment is used to
feed the material):____
- Bulk Density: _____t/m3
- Material temperature: _____℃;
- Downstream equipment (Ps. It means what kind of equipment is used
to discharge the material): _____
- Water content:____%
- Material is corrosive or not: ____ (Ps. Yes or No)
- Working power supply: _____V ______HZ
- Material is sticky or not: ____ (Ps. Yes or No)
- Working environment is indoor or outdoor: _______
- Working environment temperature: ______ ℃
- Please refer to the following picture and provide the relevant
parameters:L1____m, L2___m, H___m, α____°
Operation regulation and maintenance
- Belt conveyor should be operated in according to design
requirement.
Belt conveyors are not allowed to overload run.
All safe alarming should be in good condition.
Check wear condition of the belt, the damaged should be repaired.
Operators should circuit to inspect to close observe belt conveyor
running. Especially,temperature rise and noise of main motor and
the brake working whether they are normal; contact state of the
brake and oil level, noise of gear unit and run off of belt should
be noticed;temperature rise and noise of all bearings and state of
all transition loads point should be noticed;
notice to see whether the hopper are blocked, working state of
pulley, idler, belt cleaner, take-ups and control equipment.
Company Profile
Xinxiang Jinrui Machinery Factory is located in Xinxiang city,
Henan province ,China. In 1999 year, our company was known as
Xinxiang county mechanical and electrical equipment factory and we
changed the company name as Xinxiang Jinrui Machinery Factory in
2001 year. Our company has 3000 square meters of standardized
production workshop. Company has developed into a set design,
development, production, manufacturing, sales in the integration of
high-tech enterprises.

Our company has passed CE , ISO9001 quality management system
certification and has professional technical team, sales team and
production team. We supply our professional service with CAD & 3D
design.

Main products: Belt conveyor machine, sidewall belt conveyor,
enclosed belt conveyor, inclined belt conveyor, troughed belt
conveyor, U trough screw conveyor, tubular screw conveyor,
reversible belt conveyor,impeller feeder, vibratory feeder, movable
belt conveyor,circular vibrating sieve,small vibrating screen,heavy
duty belt conveyor
