Medical Infrared Thermometer Non Contact Celsius / Fahrenheit Mode Selectable

Medical Infrared Thermometer Non Contact Celsius / Fahrenheit Mode Selectable

Instructions

1) Power on
2) Point the infrared detector part to the center of the forehead—above the center of the eyebrow and keep it

vertical. The measurement area must not be covered by hair. If there is sweat, it should be dried.
3) The body temperature is displayed on the screen, the value is recorded, and the temperature measurement is

completed.

Parameter

Measurement range (ET305): -50 ° C to 1050 ° C (-58 ° F to 1992 ° F).
Spectrum range: 8 to 14 um.
Infrared temperature measurement accuracy: ± 1.8% or 1.8 ° C (4 ° F).
T-C temperature measurement accuracy: ± 1% or 1 ° C (2 ° F) (assuming that the ambient operating temperature is

23 to 25 ° C (73 to 77 ° F) below 0 ° C original base + 1 ° C, below -35 ° C is for reference only).
Repeatability: ± 0.5 ℃ or ± 0.5% of reading.
Response time (95% S): 250 ms.
ET305 optical resolution (D: S): 50: 1.
Emissivity adjustment: 0.10 ～ 1.00.
Display resolution: 0.1 ° C (0.1 ° F) (0.2 ° C below 10 ° C; 1 ° C / 1 ° F above 999.9).
Secondary display information: maximum, minimum, difference, average.
laser:
Aiming: single point laser;
Power: Class 2 (II) operation; output <1 mW, wavelength 630 to 670nm.
Electrical indicators:
Power: 6F22 9V battery;
Power consumption: about 30 hours battery life (alkaline), about 10 hours battery life (carbonity).

Precautions:

1. Please read the instructions carefully before measuring, and the forehead should be kept dry and the hair should

not cover the forehead. (Please measure in the environment of 10 ℃ -40 ℃) to ensure the accuracy of the

measurement.
2. The forehead temperature quickly measured by this product is for reference only and should not be used as a

basis for medical judgment. If abnormal temperature is found, please use a medical thermometer for further

measurement.
3. Please protect the sensor lens and clean it in time. If the temperature change during use is too large, it is

necessary to place the measuring device in the environment to be measured for 20 minutes, and then use it after it

has stably adapted to the ambient temperature, and then a more accurate value can be measured.

Note

A warning describes actions that may cause a hazardous situation to the user. To avoid electric shock or personal

injury, follow these guidelines:
Do not aim the laser directly at your eyes or indirectly reflected surfaces. Before using the thermometer, check

the case. If the thermometer is damaged, do not use it. Look for damage or missing plastic parts. Replace the

battery as soon as the battery indicator "" appears. Do not use the thermometer if it is malfunctioning. Instrument

protection may have been compromised. If in doubt, send the thermometer for repair. Do not use the thermometer near

explosive gases, vapors or dust. To avoid the risk of burns, keep in mind that objects with high reflectivity will

often make temperature measurements lower than the actual temperature of the object. If this equipment is used in a

manner not specified in this manual, the protection provided by the equipment may be impaired.

To avoid damaging the thermometer or device under test, protect them from the following injuries:
From EMF (electromagnetic field) including electric welding machines, electric induction heaters, static

electricity, thermal shock (caused by large or sudden ambient temperature changes-wait 30 minutes to stabilize the

thermometer before use). Do not leave the thermometer on or near hot objects. Various symbols and safety signs on

the thermometer and in the manual.

Beijing Global Dowin Technology CO.,LTD is specialized in innovation and cost effective medical thermometer. Our commitment to continuous improvement of our manufacturing processes, enhancing product performance and developing new cost-effective products to meet the demands of various customers and markets. All of our products comply with international quality standards, such as CE, FDA.

Our business philosophy is to develop mutually beneficial and nice long term relationships by providing the newest cost-effective high quality products with fastest delivery cycle and the best customer service to our customers. Customer satisfaction is always our mission and goals. Our company always regards innovation and superior consciousness as a means of continuous improvement, through to the work of every aspect of every aspect to achieve what the customers want, consider what the customers have didn't think’’ is our working principle. We will continue to strive for innovation, to introduce more new products. Welcome old and new customers wholeheartedly, looking forward to working with you to create a better future!