Hot Dip Galvanised Power Pole 166KV 38m For Power Transmission Line

38m galvanized power pole, 166kv Steel Pole for Power Transmission Line

Product Description

The products above are 38m galvanized power pole, 166kv Steel Pole for Power Transmission Line

Product Specifications
38m galvanized power pole, 166kv Steel Pole for Power Transmission Line
Material
1.) BASEPLATES
ASTM A633 Grade E
Standard for Normalized High Strength Low Alloy Structural Steel Plates
YS 415 minimum
TS (550 - 690)
EL 18% minimum
2.) ANCHOR BOLTS
ASTM A615 Grade 75
Standard for Deformed and Plain Carbon-Steel Bars for Concrete Reinforcement
YS 520 minimum
TS 690 minimum
EL 6% minimum
3.) ANCHOR BOLT NUTS
ASTM A563 Grade C
Standard for Carbon and Alloy Steel Nuts
Proof Load = 993 N/mm2 minimum
Hardness: Brinell (143 - 352) / Rockwell (B78 - C38)
4.) GROUNDING NUTS
ASTM A276 Type 304
Standard for Austenitic Stainless Steel Fasteners
YS 207 minimum
TS 518 minimum
EL 20% minimum
5.) WELDING MATERIAL
AWS D1.1 E70XX
YS 400 minimum
TS 480 minimum

The specification reference the following standards

Packaging & Shipping

We cover the top and bottom parts of the pole with a mat or straw bale in order to protect it from damage to the galvanized surface that may occur during transportation. Packaging can also be done according to clients’ requirements.

Tests

Type tests (essais de qualification)

• The performance tests of poles shall be borne by the supplier.
• EDCL requires that the following performance tests must be conducted in presence of a representative of EDCL before the first delivery.

Coating Quality control:

In accordance with ISO 1461 standards or equivalent: Thickness Control of galvanization coating and Quality control of zinc (bath of galvanization).

Tests on poles (Mechanical tests)

Non-destructive bending test (checking of the elastic limit), It is the checking of the withstand of the pole subjected to a strain F applied to the top of the embedded pole; F = (nominal tensile tension x safety factor) + fictitious

Pressure of the wind.

Method of test:

The method consists of increasing slowly and regularly the load applied to the pole from 0 to F, and meanwhile noting the variation of sag (bending of pole) corresponding to the following loads: 25% F, 50% F, 75% F, 80% F, 90% F and 100% F.

After lasting 1 mn under the load F, the pole is discharged slowly and regularly until no-load (zero load). The residual sag will be noted down. The test is satisfactory if the residual sag does not exceed 2% of the sag corresponding to 100% F load, and neither disorder nor deformation appears on the pole.

Breaking Test

Loads are applied to the pole already subjected to the deflection test under the same conditions as those specified, however the progression of the loads is carried out continuously and non-stop until pole break occurs.

The value of the load leading to pole breaking will be noted down. The breaking stress must be equal to or higher than F.

Quality control of steel

A report relating to the quality of steel intended for manufacturing of the ordered poles, and in accordance with steel quality control of EN 10025 standard or equivalent must be provided to EDCL.

Acceptance tests

Acceptance tests shall be done in factory and will be borne by the supplier. Tests will be sanctioned by statements signed by the present parts. EDCL reserves the right to be represented in these tests.

Sampling will be done in accordance with the stipulations of the international standard and on the following basis:

• Level of control: S2
• Normal simple control: it is supposed that moving to reduced or reinforced control will be done in accordance with the stipulations of the abovementioned standard.
• Acceptable Level of quality (ALQ): 2.5. Moving from normal control to reduced or reinforced control will be made in accordance with the international standard.

Acceptance tests shall include the following tests:

A. visual and dimensional monitoring of poles; finished visual aspect inspection

• Well finished welding: blisters absence, filling and cuttings of soldering wire.
• Well finished galvanization: absence of extra thickness, needles, remains flow, joining and black spots.

B. Dimensions Inspection

• Dimensional Characteristics: Height, dimensions at the top end and the base.
• Presence of mechanical protection at the top and at the base of the pole.
• Thickness Control of galvanization coating. In accordance with the international standard.

Process of Production

Verification of Materials → Cutting → Molding or Bending → Vertical Welding → Verification of Dimensions → Flange Welding → Hole Drilling → Calibration→ Deburring Process → Galvanizing, Powder Coating or Painting → Recalibration → Threading → Packaging

FAQ

Our company focuses on manufacturing all kinds of metal poles. This includes steel power poles, street lamp poles, telecommunication poles and many more. Futao Metal Structures was founded in 2000 with one goal in mind - to provide quality products that you can count on. Since then, we have accumulated 18 years of experience in international trade while our products have been used in construction projects all over the world. We are committed to living by our company motto “Quality and Integrity above all else”.

We have deep technical knowledge in the field of power distribution, advanced production equipments and experienced staff. We strive to provide the best quality in all our products. Over the years, we have developed good relationships with customers from all over the world including southeast Asia, the Middle East, America and Africa.