

Add to Cart
1200 1100 model water wet pan mills with double two rollers
Wet pan mill is mainly used for selecting gold, silver, iron and other
non-ferrous metals. It is highly efficiect and energh-saving, with
large capacity, low power consumption, small site occupation area,
and short preparation and installation time. The product has the
advantages of strong grinding ability, resource saving, reduced
repeated grinding, improved quality, no destructive impact and
vibration, simple and fast operation, solid and reliable quality,
and long service life.
Product picture
Working principle
Wet pan mill mainly through the raw material stirring, rolling,
crushing, rolling repeatedly to achieve water balance, uniform
ratio, low gas content, improve the molding rate and molding
quality, through the machine grinding material molding products,
with high density, good strength, no porosity ratio and other
characteristics. High efficiency and energy saving, high output,
the product is used for the recovery of tailings in the iron ore
process, does not make the loss of mineral powder, so that
effective resources can be fully utilized.
High efficiency and high capacity: The castings are made of high quality casting steel lining, which greatly increases the service life and the capacity by 30%-60%.
Low invest: Wet pan mill can achieve the same grinding effect as a ball mill, but the cost is much lower than that of a ball mill. It is the fastest way for small and medium-sized miners to obtain pure gold without large investments.
Low maintenance cost: The grinding rollers and grinding rings are made of high quality casting steel alloy, ensuring a service life of at least 3 years, reducing maintenance and spare parts replacement costs for customers.
Energy saving and high resource utilization : The surface of the roller and ring is smooth without any holes or cracks to avoid the loss of mercury or gold, so that the wet pan mill can make full use of effective resources.
Low pollution: We can provide sealing covers for wet pan mills to reduce air pollution.
Specification
Model | Type (mm) | Max feed | Capacity(t/h) | Power(kw) | Weight(ton) |
1600 | 1600x350x200x460 | <25 | 1-2 | Y6L-30 | 13.5 |
1500 | 1500x300x150x420 | <25 | 0.8-1.5 | Y6L-22 | 11.3 |
1400 | 1400x260x150x350 | <25 | 0.5-0.8 | Y6L-18.5 | 8.5 |
1200 | 1200x180x120x250 | <25 | 0.25-0.5 | Y6L-7.5 | 5.5 |
1100 | 1100x160x120x250 | <25 | 0.15-0.25 | Y6L-5.5 | 4.5 |
1000 | 1000x180x120x250 | <25 | 0.15-0.2 | Y6L-5.5 | 4.3 |
Wet pan mill operating rules
1. The operator must be trained by the manufacturer and fully
understand the structure and performance of the machine before they
can operate. The operator must comply with the relevant safety and
shift transfer system.
2. Before work, strictly follow the lubricating oil regulations to
refuel, and keep the oil amount appropriate, the oil circuit
smooth, and the oil injection port clean.
3. Check whether the circuit, electrical parts, line connectors,
switches are solid and complete. If there is damage, it must be
repaired and replaced.
4. Check whether the parts of the machine are intact, whether the
roller rotates flexibly, the tightness of the transmission belt,
and whether the transmission parts are securely connected; After
the inspection is completed, the boot idling for 3-5 minutes,
confirm that the parts are normal, before adding the ore, and must
be added in strict accordance with the prescribed amount of ore, it
is strictly prohibited to overload work.
5. When feeding the ore, the material must be sifted to prevent
hard metal debris such as iron blocks from being put into the mill
and damaging the machine.
6. When stopping for some reason, the material in the roller should
be removed first, and then started. It is strictly prohibited to
forcibly start with heavy load.
7. When the machine is in operation, the operator shall not leave,
and should often inspect the working conditions of various parts.
In case of abnormal sound of the equipment, large vibration of the
roller, excessive temperature of the reducer oil, overheating of
the motor housing, and slip of the transmission belt, the machine
should be shut down immediately.
8. During the shutdown process, when the roller is not completely
stopped, it is not allowed to extend the arm and other instruments
into the roller basin to prevent injury and damage to the machine.
Spare Parts
Working site
We also supply
Contact us