Drilling Mud Single Screw Pump

APG Screw pump for feeding decanter centrifuge in drilling mud system

APG Screw pumps Screw pump is also called a Progressive Cavity Pump. A screw pump is a type of rotary pump which is equipped with a rotor and stator. The rotor and stator are combined together and rotate within a cylindrical cavity or liner. The fluid or transfer medium enters from the suction side of the screw pump and moves linearly along these intermeshing screws/rotors to the discharge side of the pump.

Screw pumps mainly consisted of the discharge port, the stator, the rotor, the flexible section, the middle axis, suction room, seal, bearing, driveshaft, bearing body. Among these parts, the wearing parts are the rotor and stator. The screw pump wet parts can be made of stainless, steel, and high-quality rubber. According to different fluids' content and property, we'll provide a certain configuration on screw pumps. For example, the abrasive material we kindly suggest use the special rubber instead of stainless steel. As we know, the S.S can't adapt abrasive material but corrosive material. Compared to other pumps, the screw pump is not easy to lead swirl. This helps much to maintain pump capacity. It is not sensitive to viscosity so it is capable to transfer material with high viscosity.

Screw pump is a popular feeding pump type for centrifuge, no matter for decanter centrifuge, 3-phase centrifuge, or disc centrifuge. Besides the screw pump, a submersible slurry pump and sand pump are also been used as a centrifuge feeding pump. But as submersible slurry pump and sand pump are both a kind of centrifugal force pump, they are not as good as screw pump to feed for decanter centrifuge.

Decanter centrifuge is a high-speed rotating device. There will be many self-protection functions for safety and also to protect the device. A major self-protection application is overload protection. It means in case the centrifuge feeding is overload, the centrifuge will be stopped to avoid damaging bearings or damaging rotating components. In this case, the feeding screw pump must be capable to adjust the feeding flow. There are mainly 2 ways to control the feeding screw pump input flow rate:

1. If a fixed speed screw pump is used to feed for decanter centrifuge, a VFD control panel is requested to adjust the feeding flow rate to avoid overload and to reach a better separation performance.
2. If a manually adjustable speed screw pump is used as a decanter centrifuge feeding screw pump. A fixed speed control panel can be used for the pump to start and stop.

Screw pump transfer drilling fluid via the screw conveyor rotation. Center screw pole is the positive pole, the two sides screw conveyor are negative pole. Negative poles rotate in opposite direction with the positive pole.

Actually, when the screw axis is rotating, the lower Vroom will become large. Vroom will close against fluid sucked. The closed room will be pushed forward along the axle. Then the new suction cavity generates on suction end. One and one closed cavity move forward, the fluid will be pressed out.

How to select a screw pump?

Yes. It's depending on the centrifuge flow rate request. The screw pump APG series holding capacity from 8m³/h-350m³/h. Besides the solids control system, a screw pump can be used in other applications, too. For the drilling mud process, the centrifuge feeding pump is a rather typical use of a screw pump. Compared to other pumps, screw pumps holding shorter life or operation life considering the wearing parts. But it's a compact and high effect, many users prefer it then

Please check below technical specifications for your reference.

For any interest or demand on the centrifuge screw pump, please feel free to contact us. You will get a free offer very soon.

AIPU Solids control is professional manufacturer on solids control equipment and system. The solution for drilling mud process as well as the drilling waste management, and the oli sludge treatment system.

All items can be used in oil and gas drilling, the oil sludge treatment, the HDD mud recycling, the civil construction micro tunnelling, the piling and so on. The main equipment inlcuding solids control system, shale shaker, mud cleaner, centrifgue decanter, degassers, agitator, mud gun, centrifugal pumps, mud tank, cuttings dryer, the mud cooling system and so on.

Pleased to say AIPU products have been delivered to many regions and conturies around the world. Including Germany, Russia, USA, UK, Kuwait, UAE, India, Indonesia, Malaysia, Singapore, Taiwan, and so on.

Our hot sales product Hunter series shale shaker is rather popular with all of our clients. The Hunter-MG and Hunter-D shale shakers can be configured as linear motion, BEM or the dual motion. For the decks, they can be double deck. For the base, they can be dual tandem or triple tandem

Another hot sales products Hunter seires mud cleaner is maintained all the good features of Hunter series shaker. And the hydrocylones are all made of high quality polyurethane. Another feature is the cones are interchangeable with famous brand ones.

Besides the shale shaker and mud cleaner, there are centrifugal pumps, mud agitators and so on equipment appreciated by our clients. New innovated mud cooling system for land oil drilling is a patented products used in SINOPEC drilling site. The performance surprised end users.

Why clients select AIPU?

It's because of high qualty and the reasonable cost happened during our cooperation. We are professional on solids control, mud process, sludge treatment. Among all the orders there are over 80% orders are repeat orders from our regular clients or recommned by them

Are you in the demand of solids control or other mud treatment-related items now? Please come to us freely. Trust you will be surprised by AIPU products and servcies. All the solutions will be optimal and soonest one.