Rogers DiClad 880 High Frequency PCB Double Layer 60mil With Immersion Gold

Rogers DiClad 880 High Frequency PCB Double Layer 60mil With Immersion Gold

(Printed Circuit Boards are custom-made products, the picture and parameters shown are just for reference)

Rogers DiClad 880 laminates are made of woven fiberglass reinforced, PTFE-based composites that offer lower dielectric constant (Dk) and dissipation factors (Df). These laminates are commonly used in filter, coupler, and low noise amplifier applications, as well as power dividers and combiners, where dielectric constant uniformity and low loss are important.

Let's take a closer look at the properties of DiClad 880. This material is woven fiberglass reinforced and PTFE-based, without any ceramic filler. Its dielectric constant is carefully adjusted through a precise mixing ratio of PTFE and fiberglass, resulting in a lower DK value of 2.17 or 2.2 at 10 GHz and a lower dissipation factor of 0.0009 @ 10 GHz. However, it is important to note that this material may have less dimensional stability than high DK materials.

In terms of thermal properties, the thermal coefficient of dielectric constant (TCDk) of DiClad 880 is relatively poor at -160 ppm/°C due to the absence of any ceramic fillers. Furthermore, the coefficient of thermal expansion (CTE) in the Z-axis becomes higher at 252 ppm/°C, resulting in weaker thermal conductivity of 0.26 W/mK.

DiClad 880 has a strong adhesion to copper, as shown by its peel strength of 14 lbs/inch after thermal stress. Additionally, both the volume resistivity and surface resistivity are good, measuring at 1.4 x 10^9 MΩ-cm and 2.9 x 10^6 MΩ, respectively. The material also has an arc resistance of greater than 180 seconds.

DiClad 880 performs exceptionally well in terms of tensile modulus, tensile strength, compressive modulus, and flexural modulus. It has a dielectric breakdown value greater than 45 kilo voltage and a material density of 2.23 g/cm³. It meets the requirements of UL94-V0 flammability standards and has low water absorption of 0.02%.

DiClad 880 also has impressive outgassing properties, with a low total mass loss of 0.01% and a collected volatile condensable material limit of 0.10%. It has a water vapor regain rate of 0.01%, indicating resistance to water vapor absorption, and no visible condensate is present during use. These parameters demonstrate that DiClad 880 is highly stable and reliable.

DiClad 880 PCBs are available in various layer counts, including single-sided, double-sided, multilayer, and hybrid PCBs, and come in different dielectric thicknesses of 20mil (0.508mm), 30mil (0.762mm), and 60mil (1.524mm). They are also available in copper weights of 1oz (35µm) and 2oz (70µm), allowing for flexibility in design.

The PCB size is limited to 400mm by 500mm but can be manufactured to fit various applications. The solder mask comes in a range of colors, including green, black, blue, yellow, and red.

The surface finish of the DiClad 880 PCB is customizable and available in different options, including immersion gold, hot air soldering level (HASL), immersion silver, immersion tin, bare copper, OSP, and pure gold plated, among others.

DiClad880 PCBs are versatile and find utility in a variety of applications, including radar feed networks, commercial phased array networks, low loss base station antennas, and guidance systems.

Finally, DiClad 880 material is compatible with both traditional electroless copper and direct deposit metallization processes, making the fabrication process simple and convenient. Most surface finishes, such as HASL, tin, silver, nickel/gold, and OSP, have been applied to DiClad 880 without any issues or special concerns.

PCB Specifications

Company Profile

Founded in 2003, Shenzhen Bicheng Electronics Technology Co., Ltd is an established high frequency PCB supplier and exporter in Shenzhen China, severing cellular base station antenna, satellite, high frequency passive components, microstrip line and band line circuit, millimeter wave equipment, radar systems, digital radio frequency antenna and other fields worldwide for 18 years. Our high frequency PCBs are mainly built on 3 high frequency material brands: Rogers Corporation, Taconic and Wangling. Dielectric constant ranges from 2.2 to 10.2 etc.

Bicheng PCB is headquartered in Shenzhen, a city with great economic vitality. Based in China, we adhere to the philosophy of servicing small and medium sized companies offering variety of circuit boards to meet the demands of market.

Main Business & PCB Applications

We maintain the highest standards which support products that exhibit exceptional quality, performance and reliability. We also have divisions of FR-4 circuit board, flexible circuits and metal core PCBs featured as prototypes, small runs to mass production. We actively research and build such high value added PCB projects as HDI, quick turn, impedance control, heavy copper and backplane board etc. This has made our PCB products generate an effective prolongation and complementation, as well as formation of integrated products line ranging from low-end to high-end.The circuit boards are used in the industries of home appliances, portable and consumable electronics, medical filed, aerospace as well as telecommunications etc.

Main Material Partners