LVT 2mm PVC Flooring Tiles Slip Resistance Cherry Wood Surface

2mm PVC Flooring Tiles Slip Resistance Size Customized

• Introduction Of LVT Flooring Cherry Wood:

Function: The surface of the PVC floor has been specially treated, and some excellent stone plastic floor surfaces are also specially added with agents, which have strong killing ability for most bacteria and the ability to inhibit the growth of bacteria.

• To go the extra mile in understanding LVT, let’s take a look at how it’s made. LVT is manufactured through the following five primary processes.

1.Research and Development

From the beginning, research and development teams aim to simulate and evaluate new innovative concepts through trial and error. Large amounts of raw materials are mixed so that the team can study their interactions. The raw materials used in the production of LVT include polyvinyl chloride resins (PVC) and calcium carbonate. Once the team has a satisfactory compound to work with, it is ready to begin the calendering process.

2. Calendering Process

The calendering process uses a series of heated rollers to “roll or squeeze” the compound into a continuous sheet. By manipulating the rolls, the width and thickness of the sheet can be controlled with precise accuracy and consistency. Once the sheet is passed through the heated rolls, it is then sent through a cooling section and sent to lamination.

3. Lamination Process

Through the use of heat and pressure, lamination is a continuous process that bonds one layer to the next until all layers are fully formed. The tiles are constructed of the following four layers:

Backing layer – Sound absorbing layer with textured grip Fill layer – Stability layer for indentation resistance Print layer – Certain premium types of LVT come manufactured with realistic, 3D visuals that can be installed to resemble ceramic or stone. Wear layer – The wear layer plays a crucial role in the lifespan of your tiles. Clear coatings such as aluminum oxide will keep your flooring from rapidly wearing.

4. Embossing Process

Here, under heat and pressure, engraved rollers apply the textured design onto the face of the product which can be a light “tick” or a “deep” emboss. Once the texture is applied, the scratch and scuff Top Coat will be applied. The slabs then pass through an annealing oven that uses heated air to raise the temperature of the entire slab to a point that any stress between the layers are relieved. Once cooled back down, this process is added “insurance” to produce a stabilized product that will reduce the opportunity for “doming or cupping” due to stresses between the layers in the finished planks. From there the slabs are palletized and taken to Inspection, the final stop.

5. Inspection Process

During inspection, the slabs are brought into an air controlled room that will maintain the same temperature year round. This is important because it keeps the product in a uniform state during the milling process which helps to ensure consistent milling from one board to the next. Being able to inspect each slab before milling allows technicians to inspect and mark defective areas. The non-defected slabs will then be loaded into the press which offers alternative product sizes and is then sent to milling. Once milled, the product is boxed, wrapped, stacked on a pallet, and ready for shipment.

• Maintenance:

1. Floor must be placed at the entrance of buildings to avoid sand and dust entering through shoelaces.

2. The ground that sunlight can direct to may contract and change color, so curtain must be installed to block sunlight.

3. PVC floor material may be due to furniture, sofa, household appliances bottom rubber gasket caused discoloration, so the use of protective materials (silver, paper) isolation.

4. When moving heavy objects such as furniture and piano, pay attention to avoid scraping and bumping on the ground. The feet of steel furniture should be equipped with rubber protective pads to prevent floor loss.

5. Do not place burning cigarette butts on the floor to prevent burning the floor.

You are welcomed to contact us through email.

sales@wellful-vinyl.com

Whatsapp:+86-13057223323

Wechat:+86-13057223323

Wuxi Wellful Decoration Materials Co., Ltd was built in 2013, which specialized in producing vinyl floorings .Our new factory is located in Jiangsu China, where only has 400 kilometers distance from Shanghai Port, And we have professional staffs and advanced production lines. By organizing employee s to study and visit other companies keep us developing with market.
We spare no effort to enhance the quality. Advanced equipments, abundant technical ability and scientific management guarantee the high quality. Our products are advantageous on waterproof, soundproof, rust-resistance and anti-aging, which make us enjoy a good reputation in abroad and oversea. Until now, we have established pleasant business relationship with many customers of South America, Middle East, Africa and South Asia, etc.
We sincerely welcome all domestic and foreign customers to visit our factory, explore business opportunities and create the wonderful future together.