

Add to Cart
XPON ONU 1G1F+ CATV+ WIFI Optical Interface SC / APC Connector
Description:
designed as HGU (Home Gateway Unit) in different FTTH solutions.
The carrier-class FTTH application provides different services.
based on mature and stable, cost-effective XPON technology.
adopts high reliability, easy management, configuration flexibility
and good quality of service guarantees to meet the technical
performance of EPON Standard of China Telecom CTC3.0 and GPON
Standard of ITU-TG.984.X
Functional Feature:
Support EPON/GPON mode and switch mode automatically |
Support Route mode for PPPoE/DHCP/Static IP and Bridge mode |
Support IPv4 and IPv6 dual mode |
Support 2.4G WIFI and Multiple SSID |
Support CATV interface for Video Service and remote control by Major OLT |
Support LAN IP and DHCP Server configuration |
Support Port Mapping and Loop-Detect |
Support Firewall function and ACL function |
Support IGMP Snooping/Proxy multicast feature |
Support TR069 remote configuration and maintenance |
Specialized design for system breakdown prevention to maintain stable system |
Specification:
PON Interface | 1 GPON BOB (Bosa on Board) |
Receiving sensitivity: ≤-28dBm | |
Transmitting optical power: +1~+4dBm | |
Transmission distance: 20KM | |
Wavelength | TX: 1310nm, RX: 1490nm |
Optical Interface | SC/APC Connector |
Design Scheme | RTL9602C+RTL8192FR BOB(RTL8290B) |
Flash | SPI Nor Flash 16MB |
LAN Interface | 1 x 10/100/1000Mbps(GE) and 1 x 10/100Mbps(FE) auto adaptive Ethernet interfaces. Full/Half, RJ45 connector |
Wireless | Compliant with IEEE802.11b/g/n, |
Operating frequency: 2.400-2.4835GHz | |
support MIMO, rate up to 300Mbps, | |
2T2R,2 external antenna 5dBi, | |
Support: Multiple SSID | |
Channel: Auto | |
Modulation type: DSSS, CCK and OFDM | |
Encoding scheme: BPSK, QPSK, 16QAM and 64QAM | |
CATV Interface | RF, WDM, optical power : +2~-15dBm |
Optical reflection loss: ≥45dB | |
Optical receiving wavelength: 1550±10nm | |
RF frequency range: 47~1000MHz, RF output impedance: 75Ω | |
RF output level: 78dBuV | |
AGC range: -13~+1dBm | |
MER: ≥32dB@-15dBm | |
LED | 9 LED, For Status of WIFI,WPS,PWR,LOS,PON,LAN1~LAN2, Worn, Normal(CATV) |
Push-Button | 3,For Function of Reset, WLAN, WPS |
Operating Condition | Temperature: 0℃~+50℃ |
Humidity: 10%~90%(non-condensing) | |
Storing Condition | Temperature: -30℃~+60℃ |
Humidity: 10%~90%(non-condensing) | |
Power Supply | DC 12V/1A |
Power Consumption | ≤6W |
Dimension | 180mm×107mm×28mm(L×W×H) |
Net Weight | 0.24Kg |
Panel lights Introduction
Pilot Lamp | Status | Description |
WIFI | On | The WIFI interface is up. |
Blink | The WIFI interface is sending or/and receiving data (ACT). | |
Off | The WIFI interface is down. | |
WPS | Blink | The WIFI interface is securely establishing a connection. |
Off | The WIFI interface does not establish a secure connection. | |
PWR | On | The device is powered up. |
Off | The device is powered down. | |
LOS | Blink | The device doses not receive optical signals or with low signals. |
Off | The device has received optical signal. | |
PON | On | The device has registered to the PON system. |
Blink | The device is registering the PON system. | |
Off | The device registration is incorrect. | |
LAN1~LAN2 | On | Port (LANx) is connected properly (LINK). |
Blink | Port (LANx) is sending or/and receiving data (ACT). | |
Off | Port (LANx) connection exception or not connected. | |
Worn (CATV) | On | Input optical power is higher than 3dbm or lower than -15dbm |
Off | Input optical power is between -15dbm and 3dbm | |
Normal (CATV) | On | Input optical power is between -15dbm and 3dbm |
Off | Input optical power is higher than 3dbm or lower than -15dbm |
Application