Moistureproof 48W LED Explosion Proof Lighting for paint booth

Moistureproof 48W LED Explosion Proof Lighting For Paint Booth

Moistureproof And Waterproof IP65 LED Security Flood Light Use In Factories

Product Features:

1. Explosion proof design, high and low temperature resistance
2. The lifetime of the light source reaches 100000 hours
3. Multiple installation methods
4. Good heat dissipation
5. Dustproof, moistureproof and waterproof

Benefits:
• Energy-efficient: compared with conventional lighting, LED consumes up to 85% less energy.
• Long life: last to 100,000h rated life o more
• High light efficiency: dedicated honeycomb mirror enhance bigger lighting area, uniform illumination.
• Horizontal tri-chamber constructure, ensures LED heat will not affect driver and wiring parts.
• Optimized heat sink: aluminum housing with air diversion structure removes heat from the LEDs and driver to ensue longer life.
• Excellent 180° illumination, meet high illumination demand.
• Wide voltage range: AC200V
• Multi-protection: constant current with short-circuit and overvoltage protection.
• Good EMC: excellent electromagnetic compatibility and anti-interference.
• SMT technology: surface mounting technology keeps low working temperature of LED chip.
• Standard material: copper-free Aluminum housing, surface with epoxy powder coating, tempered glass and stainless steel external hardware.

Product structure features and working principle:
This series of products are mainly composed of LED components and driving power supply, integrated heat dissipation flameproof shell, cable lead-in device, and special tempered glass transparent parts. When the power is turned on, the drive circuit drives the LED to emit light in a constant current mode according to the set operating voltage.

Scope of application:
This series of products are suitable for hazardous environments containing explosive gases or vapors or combustible dust in Zone 1, Zone 2, Class IIA, IIB, Group T1--T6, and various indoor and outdoor operations (oil fields, metallurgy, electric power, railways, mines) , Port, municipal and other industries) for lighting use in factories, stations, venues, railway tunnels, bridges and culverts.

Use environmental conditions:

This series of products can work normally under the following environmental conditions:
1 The altitude above sea level does not exceed 2000m;
2 Ambient temperature: -20℃～40℃;
3 The atmospheric pressure is 80KPa～110Kpa;
4 The standard oxygen content (volume ratio) in the air is 21%;
5 The average relative humidity is not more than 95% (25℃);
6 In a gas or steam or dust environment that does not damage the insulation;
7 The pollution level is level 3.

the operation method of product use:
1 The product is connected to the power supply according to the rated voltage, and the operating environment temperature is -20℃～40℃.
2 According to the needs of the site environment, determine the installation method and position of the lamp, and prepare the corresponding length of the cable with an outer diameter of Φ8～Φ14.
3 When assembling and disassembling the cable, the power supply must be cut off first, and then the upper cover can be opened.
4 When installing the cable, use an Allen wrench to loosen the 6 M6 screws on the upper shell of the lamp, open the upper cover, and then loosen the compression nut of the cable inlet, and pass one end of the cable through the compression nut, flat washer and seal The loop is introduced into the wiring cavity of the lamp body, and the L, N of the cable and the grounding wire (yellow-green wire) are respectively fixed on the wiring terminal. And check that the ground wire on the other side of the terminal should be connected to the inner ground screw. Then tighten the cable compression nut and fix the upper shell. Note: Another lead-in device with (solid) plug is used when parallel lamps are used.
5 Install and fix the lamp at the selected installation position.
6 Connect the cable to the rated voltage according to the requirements of the national standard GB 3836-2010 to illuminate.

Shenzhen Everbright Lighting Technology Co., Ltd. was established in June 2005 with a registered capital of 100 million yuan. The company's headquarters is located in Luohu District, Shenzhen, and its production base is located in Bao'an District. It is a high-tech enterprise focusing on providing professional lighting solutions for industrial enterprises. ,Is a pioneer and backbone enterprise in the field of industrial lighting in China.

With first-class product quality, good after-sales service, and higher cost performance, the company has been highly recognized and positively evaluated by domestic industrial enterprises, formed a good reputation, and created a brand image of Everbright quality and service. So far, our company has established 10 sales divisions in Guangdong, Shanghai, Zhejiang, Jiangsu, Shandong, Liaoning,Tianjin,Chongqing,Jiangxi,Hunan, Hubei, Hebei, Shanxi, Inner Mongolia,Sichuan, Xinjiang, Heilongjiang, Beijing, 22 provinces (or municipalities directly under the Central Government) including Gansu, Guizhou, Jilin, and Shanxi have set up direct offices to provide first-class state-owned pillar industrial enterprises such as major domestic power plants, railways, steel plants, oil fields, petrochemicals, coal mines, and shipyards. Lighting products and services.