Full Gigabit Industrial Managed POE Switch Fiber 4 SFP To 4 Rj45 Hardened Case

Full Gigabit Industrial POE Managed Fiber Network Switch 4 SFP To 4 Ethernet Rj45

Introduction of Fiber Network Switch

IM-FP444GW series is the 10/100/1000 Mbps 8 port Industrial POE Managed Fiber Network Switch, comply with IEEE802.3af/at, power on POE IP cameras through the Ethernet cable, simple construction, power range up to 100 meters, operating temperature-40 ℃ to + 75 ℃, meet IP40 protection degree and EMC industrial grade requirements, DIN rail installation, pass through dangerous environmental certification and comply with FCC and CE standards. The reliable industrial grade design could ensure continuous and stable operation of the automation system.

Key Features of Fiber Network Switch

1. Support power on POE IP cameras through the wireless access point (AP) of 5 categories of Ethernet cable.

2. IEEE 802.3af/at power on to 1 ~ 4 RJ45 ports

3. 4 x 10/100/1000Mbps Auto-sensing RJ45 ports

4. 4 x 1000Mbps SFP fiber port
5. 6KV Ethernet surge protection, adapt to a harsh outdoor environment
6. Support Auto MDI/MDIX
7. Flow control mode: full duplex with IEEE 802.3x standard,half-duplex with Back pressure standard
8. IEEE 802.3 10Base-T and IEEE 802.3u 100Base-TX compliant
9. A store-and-forward switching mechanism
10. Operating environment temperature:-40 ° ~75 ° c
11. Support cable diagnosis and can locate the fault point
12. Support IEEE802.3az EEE (Energy Efficient Ethernet) Management, optimize power consumption
13. Support STP, RSTP, MSTP, ITU-T G.8032 Ethernet Protection Ring(EPR)
14. Support Qos, transport classification Qos, Cos, bandwidth control
15. (input/output direction), storm suppression ,differentiated services
16. Support IEEE802.1q VLAN,VLAN port ,based Mac VLAN,IP subnet VLAN,
17. Protocol VLAN,VLAN convert, MVR
18. Support dynamic IEEE802.3ad LACP link aggregation, static link aggregation
19. Support IGMP/MLD snooping V1/V2/V3, IGMP filtrating/ modulating, IGMP searching
20. Support IGMP agent report, MLD snooping
21. Safety: based on port and Mac IEEE802.1X, RADIUS, ACL, TACACS+,HTTP/HTTPS, SSL/SSH v2
22. Support Cisco® like CLI, Web management, SNMP v1/v2c/v3, Telnet
23. Support software upgrade via TFTP and HTTP, firmware redundancy prevents upgrade failing
24. Support DHCP client/Relay/Snooping/Snooping option 82/Relay option 82
25. Support RMON, MIB II, mirror image, event log, DNS, NTP/SNTP, IEEE802.1ab LLDP
26. Support IPV6 Telnet server /ICMP v6, SNMP, HTTP, SSH/SSL, NTP/SNTP,TFTP, QoS, ACL.

• The Ethernet port supports the standard IEEE802.3af power supply. (Please specify the AT standard)
• Support dual power input power supply voltage: 48~52VDC, power output power is determined by POE load.
• Wiring method: The default wiring mode is 12, 36 (you can choose custom 45+, 78- wiring mode)
• You can select one of the electrical ports to support 60W power supply output (special instructions are required when ordering)
• Make sure that the powered devices connected to the switch's POE port are compliant with the IEEE802.3af/at standard.

Industry Standards of Fiber Network Switch

• EMI: FCC Part 15 Subpart B Class A, EN 55022 Class A
• EMS: EN 61000-4-2 (ESD) Level 3,EN 61000-4-3 (RS) Level 3, EN 61000-4-4 (EFT) Level 3,EN 61000-4-5 (Surge) Level 3, EN 61000-4-6 (CS) Level 3,EN 61000-4-8
• Traffic Control: NEMA-TS2
• Vibration: IEC 60068-2-6
• Freefall: IEC 60068-2-32
• Shock: IEC 60068-2-27
• Rail Traffic: EN 50121-4

Mechanical Information of Fiber Network Switch

Shell:Corrugated metal shell;

Safety class:IP40;

Dimension:158 x 114.8 x 60mm;

Mounting method:Din-rail mounting

Spectification of Fiber Network Switch

Lead Time of Fiber Network Switch

Packing List of Fiber Network Switch

• User Manual *1 pc
• Console Cable *1 pc
• 8 Port Industrial Managed POE Fiber Switch *1 pc
• Warranty Card *1 pc

Application of Fiber Network Switch