IP68 IP69 Robot Plug Pluggable Wet Cable Wire Robot Connector
Brand Name:FANGYU
Model Number:YS-BH-8F YS-IL-8M
Minimum Order Quantity:1 unit
Delivery Time:7-10 days
Payment Terms:TT
Place of Origin:Shanghai,China
Contact Now
Add to Cart
Verified Supplier
Location:
Shanghai Shanghai China
Address:
Room 1702. Building 4 Lane 658,GuangfulinRoad. Songiiang District Shanghai
Supplier`s last login times:
within 40 hours
Product Details
Company Profile
Product Details
Rovmaker Pluggable Wet Cable Wire Robot Subsea Connectors IP68 Ip69 of Underwater Plug and Underwater Socket
Product Description
Specification
STRUCTURE | MATERIALS AND SPECIFICATIONS |
Main | The seawater corrodes stainless steel |
Install screw | 7/16-20 UNF thread length is 15/19mm |
Socket head | Neoprene (special mixing rubber for underwater connector) |
Contact Pin | Gold-plated copper alloy, American standard pin |
Positioning pin | 303 stainless steel (2 needle Ø 3.2, 3/4 needle Ø 2, 5/6/8 needle
don't need) |
O-rings | Nitrile rubber, the imported o-rings, parker 2-014, Ø 12.42 x 1.78 |
Locking lid | Polyformaldehyde resin (POM) |
Cable plug body | Special polyether |
Install line | Teflflon, silver-plated pure copper. |
End cap | Neoprene (special mixing rubber for underwater connector) |
Cable plug | Pressure-resistant seawater special cable. |
TECHNICAL PERFORMANCE
ITEM | RATING VALUE |
Depth | 0~1000 meters |
Voltage | 300V (resistance to voltage is greater than 1500V 60s) |
Working current | 2A~16A |
Insulation resistance | > 1000 m Ω (room temperature) |
Wet insertion frequency | > 500 times |
Working temperature | (-4~60)°C |
FY Can provide complete robot pre-sales, in sales, and after-sales
services
Leading technology, meticulous management, honest service, and
customer first
At present, the company produces dozens of series and thousands of specifications of products, providing customers with a wealth of products. The company has passed ISO9001 quality management system certification, most products have passed CE certification, and all products meet ROHS environmental protection requirements.
PRECAUTIONS
Always apply grease before mating.
* Disconnect by pulling straight, not at an angle.
* Do not pull on the cable and avoid sharp bends at cable entry.
* When using a bulkhead connector, ensure that there are no angular loads.
* All kinds of connectors should not be exposed to extended periods of heat or direct sunlight.
* When using a bulkhead connector, ensure that there are no angular loads.
* All kinds of connectors should not be exposed to extended periods of heat or direct sunlight.
Greasing and mating above water (dry mate) :
* Connectors must be greased with Molykote 44 Medium(recommended
brand) before every mating.
* A layer of grease corresponding to a minimum 1/10 of socket depth
should be applied to the female connector.
* The inner edge of all sockets should be completely covered, and a
thin transparent layer of grease left visible on the face of the
connector.
* After greasing, fully mate the male and female connector in order
to secure optimal distribution of grease on pins and in sockets.
* To confirm that grease has been sufficiently applied, de-mate,
and check for grease on every male pin. Then re-mate the connector.
Greasing and mating underwater (wet mate) :
* Connectors must be greased with Molykote 44 Medium(recommended
brand) before every mating.
* A layer of grease corresponding to approximately 1/3 of socket
depth should be applied to the female connector.
* All sockets should be completely sealed, and a transparent layer
of grease left visible on the face of the connector.
* After greasing, fully mate the male and female connector and
remove any excess grease from the connector joint.
Cleaning
* General cleaning and removal of any accumulated sand or mud on a connector should be performed using spray based contact cleaner (isopropyl alcohol).
* New grease must be applied again prior to mating.
Use of Loctite
For locking metallic connectors, the use of Loctite 243 is
recommended.
INSTALLATION REQUIREMENTS
1. End surface roughness requirements Ra1.6 in the diameter of the
screw hole around 25mm when threaded hole installation.
2. Hole diameter should be between Ø 11.2 ~ Ø11.4 mm and roughness
requires Ra1.6 in the diameter of the screw hole around 25mm when
through-hole installation.
3. Before installing, make sure to apply a thin layer of silicone
oil to the o-ring, not too thick.
IP68 IP69 Robot Plug Pluggable Wet Cable Wire Robot Connector
Inquiry Cart
0