Add to Cart
Gas Cooler for gas analysis system Gas cooler dual-channel gas condenser for CEMS applications
A gas cooler, also known as a gas condenser or gas conditioning system, is an important component of a gas analysis system. It is used to cool down the sample gas before it enters the gas analyzer or other downstream measurement devices. The purpose of the gas cooler is to remove excess moisture and reduce the gas temperature to appropriate levels for accurate and reliable analysis.
Here are some key features and functions of a gas cooler in a gas
analysis system:
1. Cooling Function: The primary function of a gas cooler is to
reduce the temperature of the sample gas. This is important because
high gas temperatures can interfere with the accuracy and
reliability of the analytical measurements. Cooling the gas helps
to stabilize the gas composition and minimize the influence of
temperature variations on the analysis results.
2. Moisture Removal: Gas coolers often incorporate a condensation
process to remove moisture from the sample gas. Cooling the gas
below its dew point causes the water vapor to condense, allowing it
to be separated from the gas stream. This is crucial because
excessive moisture in the gas can affect the accuracy of certain
gas analysis techniques and cause corrosion or damage to the
analyzer.
3. Heat Exchange: Gas coolers typically employ a heat exchanger
design to transfer heat from the sample gas to a cooling medium,
such as air or water. The heat exchanger facilitates efficient
cooling while maintaining a consistent flow of the sample gas.
4. Temperature Control: Gas coolers may include temperature control
mechanisms to maintain the gas temperature within a specific range.
This ensures that the gas entering the gas analyzer is at an
optimal temperature for accurate measurements. Temperature control
can be achieved through various means, such as adjusting the flow
rate of the cooling medium or using thermostatic controls.
5. Compact Design: Gas coolers for gas analysis systems are often
designed to be compact and space-efficient, allowing for easy
integration into the overall gas analysis setup. They are typically
installed near the gas sampling point or as close as possible to
the gas analyzer.
When selecting a gas cooler for a gas analysis system, consider
factors such as the required cooling capacity, the gas flow rate,
the desired temperature range, the availability of cooling media
(air or water), and any specific requirements of the gas analyzer
or the gas being analyzed. It's recommended to consult with
manufacturers or suppliers who specialize in gas analysis equipment
to ensure you choose a gas cooler that meets your specific needs
and provides optimal performance for your gas analysis system.
ESE230 Gas Cooler(Gas analyzer accessories) is a kind of compressed high efficiency moisture removing, used in gas pretreatment system of gas analysis system. It can protect moisture and corresponding corrosion to the gas analyser and guarantee the lifespan lifespan of gas analysers.
Specifications
Items | Descriptions |
Working ambient temperature | 5℃~50℃ |
Inlet gas temperature | ≤180℃ |
Inlet gas dew point | ≤80℃(@ 25℃) |
Outlet gas dew point | ≤4℃(@ 25℃) |
Condensing control temperature | Factory set at 3.0℃ |
Temperature controller fluctuation | 3.0℃±1.0℃(@ 25℃) |
Condensing method | fluoride-free compressor |
Gas condensing pipe | A+B glass heat exchange pipes, diameter * heightΦ40mm*150mm |
Inlet gas pressure | ≤3bar |
Allowed gas differential pressure range | ≤3mbar(gas flow 2NL/min) |
Gas capacity | 4NL/min |
Trouble alarm | Low temperature alarm, deviation alarm, power off alarm; alarm status dry contact output, capacity 250Vac/1A |
Peristaltic pump | 5r/min |
withstand voltage testing standard | AC1500V |
Leak current | ≤3.5mA |
Inlet gas connector | OD6mm |
Water drainage port | OD6mm |
Condensing working temperature | ≤30min |
Installation method | Wall-mounted plate installation |
Power supply | 220VAC 50Hz |
Power supply consumption | 400W |
Cabinet size(W×H×D) | 310*280*290mm |
Cabinet color | RAL7035 grey |
Weight | 18kg |
4-20mA output | optional |