The original three hole oil pump, the above introduction is a two
hole substitute
Hydraulic Paper Cutting Machine Parts 4.5KG Weight Roller Oil Pump for Polar Cutter 92
Minimum Order Quantity:1 set
Condition:New
Warranty:Unavailable
Applicable Industries:Manufacturing Plant, Printing Shops, Other
Weight (KG):4.5
Showroom Location:None
Contact Now
Add to Cart
Verified Supplier
Location:
Foshan Guangdong China
Address:
185 Heshun Avenue, Lishui Town, Foshan, Guangdong, China
Supplier`s last login times:
within 22 hours
Shipping
lt's easy to get a shipping quote! Just click the button below and complete the short form.
Get Shipping Quote
Product Details
Company Profile
Product Details
Paper cutter oil pump 2, air vent oil pump 1000-3000 r/MIN10-15mpa
for PL92 115 137 paper cutter
Pump parameter table
model： | PL-D5/3 |
Rated pressure | 10MPa |
Maximum pressure | 15MPa |
displacement | 5/3ML/r |
speed | 1000-3000min |
Detail decomposition
Another related product
Precautions for pump use
1、Working selection: 1. When selecting the pump, its rated pressure should be
appropriately higher than the working pressure to ensure the
service life of the pump and the normal operation of the system. 2.
The operating speed shall conform to the specified value of the
pump.
2、connect： 1. The connection between the vane pump drive shaft and the output
of the prime mover should preferably use an elastic coupling, with
different shaft degrees not greater than 0.05mm, and the deflection
of the two axes not greater than 5 °. Direct belt pulley driving is
not allowed. 2. When installing the vane pump, be sure to confirm
the rotation direction of the pump.
3、Tubing：The oil inlet and outlet pipes must match the pump. The suction
range shall not be greater than 50cm.
4、start-up：During initial use or operation after long-term storage, the pump
shall be filled with clean working oil before starting, otherwise
it is not allowed to start. After inching start, it shall first run
for half an hour without load. If there is no adverse phenomenon,
it shall be gradually adjusted to the required pressure. If the
pump is found to have abnormal temperature rise, leakage, vibration
and noise during operation, it shall be stopped immediately for
inspection. When stopping, it shall be unloaded first and then
stopped.
5、medium：1. When installing the hydraulic pipeline and no parts, it
must be strictly kept clean. The pipeline shall be free of any free
sundries. The solid pollution particles in the hydraulic oil are
most likely to aggravate the wear of the surface of the other parts
moving relative to the hydraulic pump. In particular, granular
impurities with a certain hardness shall be removed. 2.A filter
shall be installed at the oil inlet of the pump, and the
recommended accuracy is 100 μ m. There shall be sufficient oil
flow. Precision filter shall be set in the system, with recommended
precision of 15-25 μ m。 3.Suitable hydraulic oil shall be selected
according to the service conditions, and 32 # - 68 # ordinary
hydraulic oil is
6、tank：The oil tank shall be designed with reasonable volume to
ensure that the pump can work under normal oil temperature. A
partition shall be set in the tank to eliminate air bubbles caused
by oil return. The oil tank shall be properly sealed to prevent
impurities or dust from polluting the oil medium.
Related products
PL-115Paper cutting machine
PL920-10Turbine paper cutter
PL52Paper cutting machine
hot-sale product
Company Profile
contact information
tel：0086-75785111313 Mobile：0086-13302239101
Email:postmaster@3amachine.cn Wechat：13302239101
Hydraulic Paper Cutting Machine Parts 4.5KG Weight Roller Oil Pump for Polar Cutter 92
Inquiry Cart
0