2U Dj Class TD Stereo Power Amplifier 2*600W / 2*800W / 2*1000W
Brand Name:VATASA
Model Number:H-6/H-8/H-10
Minimum Order Quantity:2 pieces
Place of Origin:Guangdong, China
Packaging Details:soft bubble inside,thick carton outside
Price:$100.00/pieces
Contact Now
Add to Cart
Verified Supplier
Location:
Guangzhou Guangdong China
Address:
No. 36 Daping Industrial, Shatou street, Shiqiao, Panyu District, Guangzhou City, Guangzhou, Guangdong, China
Supplier`s last login times:
within 1 hours
Shipping
lt's easy to get a shipping quote! Just click the button below and complete the short form.
Get Shipping Quote
Product Details
Company Profile
Product Details
Product Description
Factory Price 2*600W 2*800W 2*1000W Class TD 2U Dj Amplifier Stereo Amplifier
1.Mains Power Switch
When press the switch, the soft start circuit run for avoiding surge strike. In about 3-4 seconds, there will be a
clicking denote that soft start finished. And more 1-2 seconds later, there will be another “clicking”, the amplifier
is connected with speaker and ready to work.
2.CH-1/CH-2 Input level control
Adjust it to get the volume desired. Use CH-1 control only while amplifier is set in Bridge or Parallel mode.
3.Signal LED
The green signal led indicates that a music signal
is present at this channel input.
4.CH-1/CH-2 Protection indicating LED
This red LED will light up when the amplifier is running un-stable or went in to thermal protection after the power
elements temperature over 90℃.
5.Clip LED
Turns on just before the maximum, distortion free, output level of the amplifier. The clip leds may turn on shortly from time to time but they may certainly not turn on for longer periods. In this case you have to turn the output level down!
When press the switch, the soft start circuit run for avoiding surge strike. In about 3-4 seconds, there will be a
clicking denote that soft start finished. And more 1-2 seconds later, there will be another “clicking”, the amplifier
is connected with speaker and ready to work.
2.CH-1/CH-2 Input level control
Adjust it to get the volume desired. Use CH-1 control only while amplifier is set in Bridge or Parallel mode.
3.Signal LED
The green signal led indicates that a music signal
is present at this channel input.
4.CH-1/CH-2 Protection indicating LED
This red LED will light up when the amplifier is running un-stable or went in to thermal protection after the power
elements temperature over 90℃.
5.Clip LED
Turns on just before the maximum, distortion free, output level of the amplifier. The clip leds may turn on shortly from time to time but they may certainly not turn on for longer periods. In this case you have to turn the output level down!
6.Bridge mode indicating LED
Indicate the amplifier is working under BRIDGE mode, the
indicator is lighten , and the input signal only acts on CH-1
7.Parallel mode indicating LED
Indicate that the amplifier is working under parallel mode,
the indicator is lighten, input signal only acts on CH-1.
8.Stereo mode indicating LED
These green LED will light up while the input signal is
connected, the amplifier is working under stereo mode.
Indicate the amplifier is working under BRIDGE mode, the
indicator is lighten , and the input signal only acts on CH-1
7.Parallel mode indicating LED
Indicate that the amplifier is working under parallel mode,
the indicator is lighten, input signal only acts on CH-1.
8.Stereo mode indicating LED
These green LED will light up while the input signal is
connected, the amplifier is working under stereo mode.
1.MAINS POWER SUPPLY CORD
2.CH-1/CH-2 SPEAKON OUTPUT
Used by a standard SPEAKON connector.
3.CH-1/CH-2 BINDING POST OUTPUT
Used by a standard binding connector.
4. OUTPUT MODE SET SWITCH.
BRIDGE MONO MODE. Sends CH-1 signals out-of-phase to CH-2,producing twice the normal voltage swing
between the two RED speaker terminals (CH-1 RED is defined as positive).Only CH-1 controls and input are
effective.
STEREO MODE. Each channel operates independently.as usual.
PARALLEL INPUT MODE. Sends CH-1 signals out CH-2,Only CH 1 controls and input are effective.
NOTE: speaker connections work as usual,Never connect the red output terminals directly together.
5. CH-1/CH-2 XLR INPUT CONNECTOR
Standard XLR (male) socket for input signal link.
Pin1: signal ground, Pin2: signal+, Pin3: signal-
6. CH-1/CH-2 XLR OUTPUT CONNECTOR
2.CH-1/CH-2 SPEAKON OUTPUT
Used by a standard SPEAKON connector.
3.CH-1/CH-2 BINDING POST OUTPUT
Used by a standard binding connector.
4. OUTPUT MODE SET SWITCH.
BRIDGE MONO MODE. Sends CH-1 signals out-of-phase to CH-2,producing twice the normal voltage swing
between the two RED speaker terminals (CH-1 RED is defined as positive).Only CH-1 controls and input are
effective.
STEREO MODE. Each channel operates independently.as usual.
PARALLEL INPUT MODE. Sends CH-1 signals out CH-2,Only CH 1 controls and input are effective.
NOTE: speaker connections work as usual,Never connect the red output terminals directly together.
5. CH-1/CH-2 XLR INPUT CONNECTOR
Standard XLR (male) socket for input signal link.
Pin1: signal ground, Pin2: signal+, Pin3: signal-
6. CH-1/CH-2 XLR OUTPUT CONNECTOR
Specification
H-6 | H-8 | H-10 | |
Power handling | 600W*2(8Ω)/900W*2(4Ω) | 800W*2(8Ω)/1200W*2(4Ω) | 1000W*2(8Ω)/1500W*2(4Ω) |
Signal to noise ratio | ≥ 95dB | ≥ 95dB | ≥ 95dB |
Output interface | Speakon and Binding | Speakon and Binding | Speakon and Binding |
Input sensitivity | 0.775V | 0.775V | 0.775V |
Input impedance | 20kΩ/Balanced,10kΩ/un-Balanced | 20kΩ/Balanced,10kΩ/un-Balanced | 20kΩ/Balanced,10kΩ/un-Balanced |
Distortion | ≤ 0.03% | ≤ 0.03% | ≤ 0.03% |
F=1KHz 8 OHMS | > 240 | > 240 | > 240 |
Frequency response | 20Hz-20kHz, ±1dB | 20Hz-20kHz, ±1dB | 20Hz-20kHz, ±1dB |
Power supply | AC: 220-230V 50Hz | AC: 220-230V 50Hz | AC: 220-230V 50Hz |
NW(kg) | 10.6 | 12.4 | 13.5 |
Size(w*d*h) | 482*326*88mm | 482*326*88mm | 482*326*88mm |
2U Dj Class TD Stereo Power Amplifier 2*600W / 2*800W / 2*1000W
Inquiry Cart
0