

Add to Cart
Property | Details |
---|---|
Brand | B&R |
Model Number | 8V1022.00 - 2 |
Product Type | Servo Drive (ACOPOS) |
Application Areas | Wood industry, textile industry, metalworking industry, and general industrial automation |
Mains Input Voltage | 3x 400 - 480 VAC ± 10% |
Frequency | 50 / 60 Hz ± 4% |
Installed Load Max. | 3 kVA |
Inrush Current at 400 VAC | 4 A |
Switch - on Interval | > 10 s |
Integrated Line Filter | Yes (per EN 61800 - 3, category C3) |
Power Dissipation at Device Nominal Power without Braking Resistor | Approx. 120 W |
DC Bus Capacitance | 235 μF |
24 VDC Power Supply Input Voltage | 24 VDC ± 25% |
24 VDC Power Supply Input Capacitance | 8200 μF |
24 VDC Power Supply Current Consumption | Max. 2.5 A + current for motor holding brake |
Motor Connection Quantity | 1 |
Continuous Current | 2.2 A eff |
Peak Current | 14 A eff |
Nominal Switching Frequency | 20 kHz |
Possible Switching Frequencies | 5 / 10 / 20 kHz |
Max. Motor Line Length | 25 m |
Protective Measures | Overload protection, short - circuit and ground fault protection |
Max. Output Frequency | 598 Hz |
Terminal Connection Cross Section (Flexible and Fine - Stranded Wires with Wire End Sleeve) | 0.25 to 4 mm² |
Approbation Data (UL / c - UL - us) | 30 to 10 awg |
Approbation Data (CSA) | 28 to 10 awg |
Motor Holding Brake Connection Response Threshold for Open - Circuit Monitoring | Approx. 385 mA |
Motor Holding Brake Connection Max. Output Current | 1 A |
Motor Holding Brake Connection Max. Number of Switching Cycles | Unlimited (implemented electronically) |
Braking Resistor Peak Power Output | 3.5 kW |
Braking Resistor Continuous Power | 130 W |
Limit Switch and Reference Inputs Quantity | 3 |
Limit Switch and Reference Inputs Circuit | Sink |
Limit Switch and Reference Inputs Electrical Isolation (Input - ACOPOS) | Yes |
Limit Switch and Reference Inputs Electrical Isolation (Input - Input) | No |
Limit Switch and Reference Inputs Nominal Voltage | 24 VDC |
Limit Switch and Reference Inputs Maximum Voltage | 30 VDC |
Limit Switch and Reference Inputs Switching Threshold (Low) | < 5 V |
Limit Switch and Reference Inputs Switching Threshold (High) | > 15 V |
Limit Switch and Reference Inputs Current at Nominal Voltage | Approx. 4 mA |
Limit Switch and Reference Inputs Switching Delay Max. | 2.0 ms |
Limit Switch and Reference Inputs Modulation Compared to Ground Potential Max. | ± 38 V |
Enable Inputs Quantity | 1 |
Enable Inputs Circuit | Sink |
Enable Inputs Electrical Isolation (Input - ACOPOS) | Yes |
Enable Inputs Nominal Voltage | 24 VDC |
Enable Inputs Maximum Voltage | 30 VDC |
Enable Inputs Input Current at Nominal Voltage | Approx. 30 mA |
Enable Inputs Switching Threshold (Low) | < 5 V |
Enable Inputs Switching Threshold (High) | > 15 V |
Enable Inputs Switching Delay (Enable 0 → 1, ready for PWM) | Max. 100 μs |
Enable Inputs Switching Delay (Enable 1 → 0, PWM off) | Max. 2.0 ms |
Enable Inputs Modulation Compared to Ground Potential Max. | ± 38 V |
OSSD Signal Connections | Not Permitted |
Trigger Inputs Quantity | 2 |
Trigger Inputs Circuit | Sink |
Trigger Inputs Electrical Isolation (Input - ACOPOS) | Yes |
Trigger Inputs Electrical Isolation (Input - Input) | No |
Trigger Inputs Nominal Voltage | 24 VDC |
Trigger Inputs Maximum Voltage | 30 VDC |
Trigger Inputs Switching Threshold (Low) | < 5 V |
Trigger Inputs Switching Threshold (High) | > 15 V |
Trigger Inputs Current at Nominal Voltage | Approx. 10 mA |
Trigger Inputs Switching Delay (Rising Edge) | 52 μs ± 0.5 μs (digitally filtered) |
Trigger Inputs Switching Delay (Falling Edge) | 53 μs ± 0.5 μs (digitally filtered) |
Trigger Inputs Modulation Compared to Ground Potential Max. | ± 38 V |
Electrical Discharge Capacitance | 660 nF |
Energy Efficiency (ie Classification) | ie2 (10, 25): 3.8% |
Permissible Mounting Orientations | Hanging vertically: Yes |
Installation Elevation above Sea Level (Nominal) | 0 to 500 m |
Installation Elevation above Sea Level (Maximum) | 2000 m |
Pollution Degree per EN 61800 - 5 - 1 | 2 (non - conductive pollution) |
Overvoltage Category per EN 61800 - 5 - 1 | II |
Degree of Protection per EN 60529 | IP20 |
Ambient Temperature (Operation - Nominal) | 5 to 40 °C |
Ambient Temperature (Operation - Maximum) | 55 °C |
Ambient Temperature (Storage) | - 25 to 55 °C |
Ambient Temperature (Transport) | - 25 to 70 °C |
Relative Humidity (Operation) | 5 to 85% |
Relative Humidity (Storage) | 5 to 95% |
Relative Humidity (Transport) | Max. 95% at 40 °C |
Dimensions (Width) | 70.5 mm |
Dimensions (Height) | 375 mm |
Dimensions (Depth) | 235.5 mm |
Weight | 4.0 kg |
Certifications | CE, UKCA, Functional safety, UL cULus e225616, Power conversion equipment (KC) |
Slots for Plug - in Modules | 4 |
Included in Delivery | Shielding component sets (8 x 0010.00 - 1 ACOPOS shielding components set for 8V1022.xxx - x up to 8V1090.xxx - x), Terminal sets (8 x 0001.00 - 1 ACOPOS accessories, connector set for 8V1010.00 to 8V1090.00 (3 - phase)) |
Optional Accessories | Plug - in modules such as 8AC110.60 - 3 ACOPOS plug - in module (CAN interface), 8AC114.60 - 2 ACOPOS plug - in module (Powerlink v2 interface), etc. |