M5 M6 Stainless steel L Type and J Type metal bolt with nut washer assortment SUS304 SUS316 A2-70 A4

M5 M6 Stainless steel L Type and J Type with nut washer assortment SUS304 SUS316 A2-70 A4

Product Description:

Uses
1,Fixed footbolt is also called short footbolt, it is poured together with the foundation and used to fix the equipment without strong vibration and shock.
2,Activity foot bolt also known as long foot bolt, is a kind of removable foot bolt, used to fix the work of strong vibration and shock of heavy machinery and equipment.
3,Expansion anchor anchor bolt is often used to fix the static simple equipment or auxiliary equipment. Expansion anchor anchor bolt installation should meet the following requirements: the distance from the bolt centre to the edge of the foundation is not less than 7 times the diameter of the expansion anchor anchor bolt; installation of expansion anchor anchor bolt foundation strength shall not be less than 10MPa; drilling holes shall not be cracked, and attention should be paid to preventing the collision of drilling bit with the reinforcement bars in the foundation and the embedded pipe; the diameter and depth of drilling holes should be matched with the expansion anchor anchor bolt.
4,Bonding anchor bolt is a kind of anchor bolt commonly used in recent years, and its method and requirements are the same

Installation

1,One time burying method: when pouring concrete, bury the ground bolt. When the tower is controlled by tilting, the anchor bolts should be buried at one time.
2,Pre-reserved hole method: When the equipment is in place, clean the holes, put the foot bolts into the holes, and then use non-shrinkage fine gravel concrete, which is one level higher than the original foundation, for pouring and compacting after the equipment is positioned and corrected. The distance from the centre of the footbolt to the edge of the foundation should not be less than 2d (d is the diameter of the footbolt) and should not be less than 15mm (not less than 10mm when d≤20), and not less than half of the width of the anchor plate plus 50mm, and when it cannot satisfy the above requirements, appropriate measures should be taken to strengthen it. The diameter of the anchor bolts for structure should not be less than 20mm. when subjected to seismic action, it should be fixed by double nuts or other effective measures to prevent loosening, but the anchoring length of the anchor bolts should be increased by 5d compared with that of the non-seismic action.

Applications

There are two main ways to judge the hardness of steel, which are Brinell hardness in HB and Rockwell hardness. Firstly, from the Brinell hardness, will be a hardness higher than the measured steel ball to the steel above, and apply a force F, then the ball will be in the measured steel will leave a dent, measured, the area of M, then Rockwell Brinell hardness will be F/M. Next Rockwell hardness is also convenient to explain the only difference between the latter and the former Rockwell hardness measurements is the force to force to divide by the depth of the small ball plunged into the.

Steel can be improved by mixing it with alloys, for example by adding carbon, known as carbon steel, which increases its hardness and rigidity but decreases its toughness and plasticity. By adding chromium, the hardness and rigidity of steel can be increased with less effect on its toughness. By adding titanium, the hardness and toughness of steel is increased.

The properties of steel can vary after different types of processing, with a focus on quenching and tempering, two of the earliest forms of steel processing that I learnt about as a child, both of which I learnt about through the game Ride and Slash. Firstly, quenching is the process of heating steel to over 723 degrees and then soaking it in water for a rapid cool down to increase the hardness and decrease the malleability of the steel. Tempering means heating the steel to over 723 degrees and then cooling it slowly to increase its strength and toughness at the same time.

About Us






Package

Hunan Jiashan Hardware Tech as a branch company of J AND R METALWORK,established in 2007 and located in Changsha, Hunan, China.After almost 17 years management development and technical improvement, Jiashan is willing to be a leading supplier in hardware industry. Meanwhile, we are one of member of Hardware industrial Association and Green energy industry Association.

Jiashan is specialized in milling,turning,lathe 5 axis cnc machining parts,injection molding parts,alumium extrusion parts,laser cutting parts,sheet metal fabrication parts,wire edm parts,vacuum casting parts and fasteners.Those parts are widely service for electric vehicle,solar system,wind power system and construction machinery industry.

During17 years domestic and abroad market investigation, Jiashan's products are sold to many countries and regions including the North America, Europe, Australia, the Middle East and Asia. With owned the advanced cnc machinee, milling machine, polishing machine, stamping machine etc. Jiashan is able to degsin and produce varies OEM parts with drawings or samples provided. Further more, Jiashan also can help to provide a whole solution for modularity R&D of electric vehicle and solar system .

By constantly strengthening our management and consummate the quality guarantee system.In 2023, Jiashan acquired ISO9001:2008 quality certification. Currently,the 5S management mode is implemented in the whole Jiashan system.

Best quality and best service is and will be always our toppest concern.