0.96 inch SSD1315 OLED Display Module Folding Type OEL Display ModulePixel Number 128 x 64 Monochrome COG Package

Brand Name:ESEN
Certification:ISO9001/ISO14001
Model Number:HP096-2864KLBAG01-H30
Minimum Order Quantity:1000PCS
Delivery Time:3-4 weeks
Payment Terms:T/T,L/C
Contact Now

Add to Cart

Verified Supplier
Location: Shenzhen China
Address: Unit 901B, 9th Floor, Block D, Cai Fu Gang International Building, Bao Yuan Road, Bao An District, Shenzhen,China
Supplier`s last login times: within 1 hours
Product Details Company Profile
Product Details

Description

HP096-2864KLBAG01-H30 is a 128x64 resolution COG graphic OLED display module, diagonal size 0.96 inch. The model is designed as consumer grade which is having the advantage of competitive price. The module is built-in with SSD1315 IC; it supports I2C and 3-wire /4-wire SPI serial interface. The supply voltage for logic is 3V, supply voltage for display is 7.5V, display with 50% check board current is 6mA @ 7.5Vcc (typical value), driving duty 1/64.HP096-2864KLBAG01-H30 module supports internal Charge Pump supply and external VCC supply.

This 0.96 inch COG Graphic OLED module is suitable for wearable device, smart home applications and etc. This module can be operating at temperatures from -30℃ to +70℃; its storage temperatures range from -30℃ to +70℃.


DRAWING

Absolute Maximum Ratings

ParameterSymbolMinMaxUnit
Supply Voltage for LogicVDD-0.34.0V
Charge Pump RegulatorVBAT-0.36.0V
Supply Voltage for DisplayVCC018.0V
Operating TemperatureTOP-30+70°C
Storage TemperatureTSTG-30+70°C

Electronical Characteristics

DC Electrical Characteristics

ItemSymbolConditionMinTypMaxUnit
Supply Voltage for LogicVDD2.83.03.3V
Supply Voltage for DisplayVCC7.07.58.0V
Input High Volt.VIH0.8×VDDVDDV
Input Low Volt.VIL00.2×VDDV
Output High Volt.VOH0.9×VDDVDDV
Output Low Volt.VOL00.1×VDDV
Operating Current for VCC (50% display ON)ICC612mA

Interface Pin Function


No.SymbolFunction
1C2NC2P/C2N – Pin for charge pump capacitor; Connect to each other with a capacitor.
2C2P
3C1PC1P/C1N – Pin for charge pump capacitor; Connect to each other with a capacitor.
4C1N
5VBATPower Supply for DC/DC Converter Circuit
This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be float when the converter is not used.
6VCCPower supply for panel driving voltage. This is also the most positive power voltage supply pin.
When charge pump is enabled, a capacitor should be connected between this pin and VSS.
7VSSGround of Logic Circuit
This is a ground pin. It acts as a reference for the logic pins. It must be connected to external ground.
8VDDPower Supply for Logic
This is a voltage supply pin. It must be connected to external source.
9BS0Communicating Protocol Select
These pins are MCU interface selection input. See the
following table:
BS[1:0]Interface
004-line SPI
013-line SPI
10I2C
10BS1
11CS#Chip Select
This pin is the chip select input. The chip is enabled for MCU communication only when CS# is pulled low.
12RES#Power Reset for Controller and Driver
This pin is reset signal input. When the pin is low, initialization of the chip is executed.
13D/C#In I2C mode, this pin acts as SA0 for slave address selection.
When 3-wire serial interface is selected, this pin must be connected to VSS.
14~16D0~D2When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
17IREFCurrent Reference for Brightness Adjustment
This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 30uA.
18VCOMHCOM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
19VCCPower supply for panel driving voltage. This is also the most positive power voltage supply pin.
When charge pump is enabled, a capacitor should be connected between this pin and VSS.
20VLSSGround of Analog Circuit
This is an analog ground pin. It should be connected to VSS externally.

Q&A

Q: Is there a Touch Panel (Touch Screen) on the display?
A: We can offer you the RTP (Resistive Touch Panel) and CTP (Capacitive Touch Panel) if you need.
Q: What about payment terms?
A: PayPal and credit card can be accepted for sample, T/T paid for mass order. Advance payment percentage can be discussed.
Q: How long can I get the goods?
A: It depends on the quantity. Our inventory is mainly raw materials, semi-finished and a small number of finished products. Samples available in stock will be sent in 3 days; Small batch delivery takes 15-20 working days include producing; Large batch delivery takes 20-30 working days. We will list the time cost for you before order.
Q: Can I trust the quality? We want good quality first.
A: Our company has a professional Quality Control Department, and all products are 100% inspected prior to ship. We welcome all the customers from the wolrd visiting our factory for checking any time


China 0.96 inch SSD1315 OLED Display Module Folding Type OEL Display ModulePixel Number  128 x 64 Monochrome COG Package supplier

0.96 inch SSD1315 OLED Display Module Folding Type OEL Display ModulePixel Number 128 x 64 Monochrome COG Package

Inquiry Cart 0