Add to Cart
Good Self-Healing Properties 2.0uf 185K 125VAC X2 Safety
Withstanding Surge Voltage Stressing
The X2 series of film capacitors are mainly used for EMI
suppression by connecting the L/N of the power input, and used in
parallel with the input port. The advantages are as follows:
1. This capacitor is very stable, with little change over time and
stability, so the input is not easily affected by environmental
factors.
2. Unlike other types of ceramic capacitors, the capacitance of
film capacitors is less affected by voltage. An X7R ceramic
capacitor has a capacitance change of 40% between 0V and 50% of the
applied voltage.
3. Unlike most types of capacitors, film capacitors have a very low
dissipation factor. This means that very little heat is generated
when AC current flows through the film capacitor. The X7R capacitor
converts 10% of the current flowing through it into heat, while the
film capacitor is less than 0.1%.
X2 Safety Capacitor.pdf
Marking
1. CIGU logo:
2. Capacitance:(104K ,0.1μF)
3. Capacitance Tolerance:(K)±10%
4. Rated Voltage:250,275,300,305,310VAC 5. Product Class:X2
6. Product type: MPX
7. Climatic Category: 40/110/56
8. Passive Flammability Class:B
9. China approvals mark:CQC
10. Germany approvals mark:VDE
11. ENEC approvals mark:ENEC
12. American approvals mark:CUL
13. Approval standard:IEC60384-14
NO. | Main Materials | Specification | Remark |
1 | Metallized polypropylene Film | MPPZAH or MPPA(5~12μm) | --- |
2 | Zn,Sn line | Zn or Zn and Sn alloy | --- |
3 | Terminal | Cu(Copper wire) (Φ0.55 or 0.75mm) | ±0.05mm |
4 | Sealed Material | Epoxy resin | UL94-V0 |
5 | Plastic Case | PBT | UL94-V0 |
Features
1.This is specifically designed for applications in serial with the
100Vac-240Vac main, i.e. capacitive divider, for example,energy
meter, LED driver etc.
2.Metallized polypropylene film
3.Good self-healing properties, withstanding surge voltage
stressing
4.Long stability of capacifance
5.Good properties in damp environment
6.Excellent active and passive flame resistant abilities
Construction and main materials of products
Specifications(IEC 60384-14)
Test items | Performance requirements | Conditions of test |
Capacitance | Within the tolerance specified | 1KHz, 1Vrms Max. at 25℃ |
Dissipation Factor | 0.001 (0.1%) Max. | 1KHz, 1Vrms Max. at 25℃ |
Voltage proof | Shall be no abnormality | Between terminals 4.3UR (Vdc) Test of 60sec. |
Between terminal and enclosure UR×200%+1500Vac, 60sec. | ||
Insulation resistance | CR ≤ 0.33μF IR ≥ 15,000MΩ CR >0.33μF IR ≥6,000s | 100±15Vdc, 60sec / 25℃ |
Robustness of terminations | No wire breakage and no damage of capacitor | Tense Strength of Terminal Load Force : 1.0 Kg |
Bending Strength of Terminal Load Force : 0.5 Kg | ||
Resistance to soldering heat | (1) Appearance : No visible damage | Solder temperature: 260±5℃ |
Solderability | 95% of the surface tinning | Solder temperature: 260±5℃ |
Rapid change of temperature | The capacitors shall be visually examined and there shall be no visible damage. | Lower category temperature: -40℃ |
Vibration | The capacitors shall be visually examined and there shall be no visible damage | Frequency range: 10~55Hz |
Test items | Performance requirements | Conditions of test |
Climatic sequence | (1) Appearance : No visible damage | Dry Heat |
Cold | ||
Damp Heat Steady State | (1) Appearance : No visible damage | +40°C and 93% RH, 56 days |
Charge and discharge | (1) Appearance : No visible damage | Test voltage : √2 x URVAC 50 Hz |
Endurance | (1) Appearance : No Visible Damage | 1.25 x UR VAC 50 Hz, once every hour |
Storage conditions
1 t should be noted that the solderability of the terminals may be
deteriorted when stored barely in an atmosphere for a long preriods
2 It shouldn't be located in particularly high temperature and high
humidity, it must submit to the following conditions(keeping in the
original package)
Temperature: 35 MAX Relative humidity:60% MAX
3 Storage period:Losse:12 monthes max (from the manufacturing date
marked on the label in package bag)
Enviroment requirement
1 Compliance with the requirement of RoHS.
2 Compliance with the requirement of REACH.
3 Without Halogen(as required).
4 Please see the attachment 2 for the test reprots of the Rohs and
Reach by a third party
Quality Control
Product structure