Product Details
GE IC200ALG620 4 POINT 16 BIT 25/100/1000 OHM PLATINUM 10/50/100
OHM COPPER 100/120 OHM NICKEL 604 OHM NICKEL/IRON
Product information GE IC200ALG620:
The IC200ALG620 is a VersaMax analog input module that is
manufactured by Emerson Automation. This module is specifically a
Resistance Temperature Detector (RTD) module that is used for
temperature measurement and integration of transducers. This module
is a 4-channel RTD / Resistance analog input module that can be
used with a variety of RTD sensors including Platinum 25, 100, and
1000 ohm; Copper 10, 50, and 100 ohm; Nickel 100 and 120 ohm; and
Nickel / Iron 604 ohms and direct input of resistance value ranges
such as 0-500 Ohms and 0-3000 Ohms.
The IC200ALG620 supports 3-wire and 4-wire RTD sensors. Each
channel has a dedicated Analog to Digital (ADC) converter circuit
with conversion resolution of 16 bits. This module has measurement
accuracy (at 25 Degree Celsius) of +/–0.15% when used for
resistance measurement and +/-0.15% on RTD (temperature)
measurement mode. Each input channel is capable of detecting Open
RTD, input short, underrange, overrange, non-volatile memory
storage fault, wiring fault and high/low alarm.
These fault and alarm conditions are reported to the host
Programmable Logic Controller (PLC) for integration. This module
has an update rate of 210 ms per channel at 60 Hz and 230 ms per
channel at 50 Hz. It is also installed with an OK LED which signals
backplane power active supplied to the module when lit Green and
module fault when lit Amber. This module has backplane current draw
of 125 mA at 5.0 VDC bus output and 125 mA at 3.3 VDC bus output.
The IC200ALG620 module is a 16-bit module manufactured by GE Fanuc.
It is an analog input module designed with 4 channels. It offers a
resolution of 16 bits. It operates with a voltage of 5 Volts and it
has an update rate of 210 milliseconds. It is equipped with LED
indicators that help the users to understand different states of
the module. It has the FLD PWR LED and the OK LED. The FLD PWRLED
shows that the backplane power and field power are present in the
circuit. The OK LED shows the normal operation of the module. It
illuminates in amber when a diagnostics error is present in the
module. The LED flashes green when the module is updating or in the
boot mode. It consumes a total of 125 milliamps of current from the
5 Volts bus.
The IC200ALG620 module has 250 Volts AC isolation for user input to
logic and 1500 Volts AC isolation for 60 seconds for user input to
frame. It consumes a total of 125 milliamps of current. It can
update at a frequency between 50 and 60 Hertz, depending upon the
channel. The common mode rejection ratio of the module is 120 dB
with a frequency of 50 to 60 Hertz with of 100% span.
The normal mode rejection stands at 60 dB at a similar frequency.
The operation temperature of the IC200ALG620 module should not
exceed 60 degrees Celsius in a clean environment. The IC200ALG620
module is easy to configure and install. During the installation
process, the module should be properly grounded to avoid electrical
damage.
More information:
Selectable resistance measurements in tenths of ohms, tenths of
degrees Fahrenheit, or tenths of degrees Celsius
Individual channel configuration
Selectable resistance ranges: 0 – 500 ohms and 0 – 3000 ohms
Selectable RTD input as resistance or temperature (Celsius or
Fahrenheit)
Reports high/low, underrange/overrange, open wire and input short
alarms.
Two data acquisition rates based on 50 Hz and 60 Hz line
frequencies
Configurable channel activation The module automatically performs
A/D calibration at powerup. Automatic calibration is then repeated
periodically to compensate for changes in the ambient temperature.
IC200ALG620's details:
Restrictions and Open Issues:
▪ Additional faults may be logged when a new configuration
containing parameter changes such as the Alarm High limit or Alarm
Low limit in the hardware configuration of an analog module is
stored followed by a Clear All operation. The additional faults are
logged against the previous configuration. This issue is observed
when Machine Edition is connected to Versamax CPUs (IC200CPU001,
IC200CPU002, IC200CPU005 and IC200CPUE05) and does not occur with
Versamax NIUs (IC200GBI001, IC200EBI001, IC200PBI001, and
IC200DBI001).
▪ When more than 20 faults are sent to a GBC70 within a single
Genius scan, under rare conditions one fault or fault contact may
not be reported by the GBC70. This has been observed when
simultaneous open wire condition occurs in all eight channels of
IC200ALG240 module or if several I/O modules in a GNIU rack
generate multiple faults simultaneously. This issue has only been
observed when the GBC70 was in a rack with an RX7i CPU.
▪ When 45 or more faults are sent to a GBC70 within a single Genius
scan, a few faults or fault contacts may not be reported by the
GBC70. This is most likely to be caused by the sudden loss of
numerous blocks at each bus controller in the system. The resulting
PLC diagnostics and diagnostic contacts may be incorrect. ▪ After
rapid power cycles or certain brownout conditions, an IC200ALG620
module may blink a 6-3 error code, indicating a hardware failure.
Cycle power to the module to restore operation.
▪ When at least one IC200ALG620 channel is configured to measure
0-3000 Ohms, other channels that are configured as active but have
nothing connected may report an Input Open Wire fault (fault code
2) rather than the expected Wiring Fault Error (fault code 4) to
the I/O Fault table.
Our brand:
Order Process:
1, First, send us the brand, model code/pic of the nameplate, the quantity for inquiry. Then we will send the quote to you. after confirming
the model and the quantity, then we will the PI to you.
2, You can transfer by Paypal/ Western Union/Trade assurance/ T/T.
When we received the payment, then we will start to prepare the
order for you asap.
3, We can according to your shipment to ship out the goods, Or we
also can help you to ship out the goods directly. And the tracking
number will send you by the next day.
4., Usually for our inventory goods only need to take about 3-5
days.
5. If you also have any questions, you can ask me any time, right
below is my contact.
FAQ
* Q: Do you provide a warranty for the goods?A: Yes, we provide a warranty for all the goods from us.
* Q: Could Wisdomlong provide technology support?
A: We're in this field for more than 8 years. If there's any
problem, please contact with us, we'll provide a suggestion from
our
engineer to help you solve the problem.
* Q: Does Wisdomlong keep goods in stock or only trading?
A: We have a large warehouse for goods. Keep lots of goods in the
warehouse, so could promise a fast delivery.
* Q: What is your MOQ?
A: We provide you small MOQ for each item, it depends on your
specific order!
* Q: Do you test all your goods before delivery?
A: Yes, we have 100% test before delivery.
* Q: How do you make our business long-term and good relationship?
A: We keep good quality and competitive price to ensure our
customers benefit ;
We respect every customer as our friend and we sincerely do
business and make friends with them, no matter where they come
from.
Send your Inquiry details in the Below, Scan "The QR Code" Now!
Company Profile
Wisdomlong Technology CO.,LTD locats at the central of China,Shenzhen, Guangdong Province. With
rapid development, Wisdomlong serves fields of automation in global
markets, Our business covers five continents throughout the world
with the basic conviction of honest, the international management
of customer-centered concept and purpose of bringing convenience to
customers. We have confidence to bring our customers more
substantial profit with high-quality service and reasonable prices.

Choosing us,you will choose a sincere friend and reliable partner.
Please feel free to contact us if you are a global manufacturer of
high quality brand products who desires to enter the Chinese market
or who searches for a Chinese agent.We would like to create a
brilliant future with friends in domestic and overseas. All goods
sold have one year warranty.
The company with domestic and international numerous well-known
brands supplier to build have extremely good relations of
cooperation, in Japan, South Korea, southeast Asia, Africa, Europe
and the United States, and formed a stable and efficient supply
network. The agent and the products are widely used in machinery,
equipment manufacturing, electric power, metallurgy, petrochemical,
automobile manufacturing industry, paper making, chemical industry,
medicine and aerospace industries.