HVAC Thermostat High/Low Pressure Switch with Adjustable Reset KP61 060L110866 +35℃ 2m

HVAC Thermostat High/Low Pressure Switch with Adjustable Reset KP61 060L110866 +35℃ 2m
◆ KP type Thermostat temperature controller is single pole double throw (SPDT) temperature control temperature switch
◆ KP-type Thermostat temperature controller can be directly with the following 2kW single-phase AC motor connected, or installed in the DC motor and large AC motor control circuit
◆ KP-type Thermostat temperature controller can be used to adjust, can also be used for security monitoring system. This shows the superiority of the electromechanical device
◆ KP-type Thermostat temperature controller has two kinds of steam and adsorption-type filling method
◆ Steam-filled KP-type Thermostat temperature controller back to a small difference
◆ KP-type adsorption Thermostat controller temperature controller is widely used in defrost protection
Product Features:
◆ Wide adjustment range
◆ can be used for refrigeration, refrigeration and air conditioning equipment
◆ Welded bellows increase the reliability of the controller
◆ Small size, easy to install in the freezer and cold storage
◆ ultra-short dithering time, long life, wear and tear reduced to a minimum, increased reliability
◆ standard switch, you can get the reverse switch function and signal display
◆ Front connection, easy to install, save space
◆ Suitable for AC and DC
◆ flexible cable with a 6-22mm diameter cable entry of a wide range of applications

Technical Parameters:

Ambient temperature -40 ~ 65 ℃ (+80 ℃ conditions, up to two hours)
Switch SPDT switch
Contact load AC: AC1: 16A, 400V AC3: 16A, 400V AC15: 10A, 400V
The maximum opening current (L.R.): 112A, 400V
DC: DC13: 12W, 220V controllable current
Wire Size Solid / Cable 075-2.5mm2 Soft / Without Metal Sleeve 0.7-2.5 mm2 Soft / With Metal Cover 0.5-1.5 mm2
Tightening torque Max. 2NM Rated impulse voltage 4kV Pollution degree 3 Short-circuit protection, fuse 10Amp
Insulation 400V IP 30/44
Wire connection
The wire interface can be used for wires with a diameter of 6 to 14 mm
Cable connection
The cable interface can be used for cables with diameters from 6 to 14 mm. A Pg13.5 spiral cable entry can be used for cables with a diameter of 6-14 mm. A cable with a diameter of 8-16 mm can use the spiral cable entry of the Pg16
shell
When the controller is mounted on a flat surface or bracket, the enclosure protection class IP30 (IEC529) can be achieved and the bracket must be secured so that all holes are covered

KP pressure controls are for use in refrigeration and air conditioning systems to give protection against excessively low suction pressure or excessively high discharge pressure. The controls are also used for starting ans stopping refrigeration compressors and fans on air- cooled condensers. KP pressure controls are available in IP 30 and IP 44 enclosures.

Product Features

1,KP Dual Pressure Controls are available in versions for regulation of high pressure on both left and right side or regulation of low pressure on left and high pressure on right side (versions with LP signal or LP+HP signals). Enclosure rating IP30 or IP44.

2,Ultra-short bounce time thanks to snap-action function (reduces wear to a minimum and increases reliability)

3,Manual trip function (electrical contact function can be tested without the use of tools)

4,Vibration and shock resistant

5,Compact design

6,Fully welded bellows element

7,High reliability both electrically and mechanically

Pressure controls are pressure-activated switches, with a basic function to make or break an electrical circuit which in tur controls a solenoid coil, a contactor or some other functioning part of the system.

The set point at which a control closes a contact and makes a circuit is called the cut-in point.

The point at which the control opens the switch and breaks the circuit is called the cut-out point.

The difference between the cut-in and cut-out point is known as the differential.

1. KP pressure controls are for use in refrigeration and air conditioning systems to give protection

Against excessively low suction pressure or excessively high discharge pressure.
2. KP pressure controls are also used for starting and stopping refrigeration compressors and fans
On air-cooled condensers.
3. KP pressure controls are fitted with a single-pole double-throw (SPDT) switch. The position of the
Switch is determined by the pressure control setting and the pressure at the connector.

Star-Worths Refrigeration Co.,ltd as a professional refrigeration equipment company

which combined Cold storage products manufacturing,after-sales service,technical consulting and many famous brands origional brand new refrigeration compressors&HVAC control tools distributor selling.

Factory have 18 years history in manufacturing refrigeration equipment: Air cooled condenser, water cooled condenser, air cooler, evaporator, liquid receiver,Condensing unit as well as various customize refrigeration parts.

They are widely used in cold room,freezer, showcase, air conditioning, ice bath, food and medical hygiene,Biological Engineering,Aquatic products,Supermarkets,electronic,Hotel services and other areas.

Factory over 40000m2 square meters area with about 300 workers.Raw material and finished products warehouse over 1000 square meters.

Has been introduced advanced production line with an annual output of above millions refrigeration equipments. Mould system, NC Punch System, Expansion machine, Spraying system, test line, etc.

Our major markets:

- Southeast Asia
- Middle East
- Australia
- South America
- North America
- Europe

You have our high quality, good credit, competitive price ,safety payment, fast delivery and excellent service .

we have a good cooperation with our refrigeration engineering, distributor, trader, retailer and manufacturer.

Thank you for your attention.