Two In One Single Phase Surge Protector , 420V 40KA Mains Surge Protection Devices
Brand Name:THOR
Certification:CE
Model Number:TRS2-C40
Minimum Order Quantity:1 piece
Delivery Time:3-7 work day
Payment Terms:L/C, T/T, Western Union, MoneyGram
Contact Now
Add to Cart
Active Member
Location:
Wenzhou Zhejiang China
Address:
China Zhejiang Wenzhou Economic Development Zone
Supplier`s last login times:
within 36 hours
Product Details
Company Profile
Product Details
Network two in one protector device, power network, signal unity protection.
Product introduction
Surge protector is an electronic device that provides security
protection for all kinds of electronic devices, instruments and
communication lines. When the peak current or voltage is suddenly
produced in the electrical circuit or communication line because of
the external interference, the surge protector can guide the shunt
in a very short time, thus avoiding the damage to the other
equipment in the circuit. It is usually installed in the floor
distribution box, computer center, telecommunication machine room,
elevator control room and so on.
Product features
1. strict product structure, meticulous and comprehensive
protection
2. strict product structure, meticulous and comprehensive
protection
3. new technology, high energy, gap discharge electrode N-PE.
Structure and Principle
SPD is a port, shocking protection, indoor-mounted installation, voltage-limited.
SPD hold disconnector inside, when SPD breakdown failure by over heating, the disconnector can remove from the power grid automatically, and show indication signal. When SPD is working properly, visible window display green, it display red when it breakdown and disconnect.
1P+N,2P+N,3P+N SPD consist of 1P,2P,3P SPD+NPE zero ground protection module, apply to TN-S, TN-C-S and other power supply system.
Product specification
| Model | TRS2-C40 | |
| Rated Operating Voitage | UC | 420 |
| Voltage protective level | Up(KV)≤ | 2.0 |
| Max discharge current | Imax(8/20μS) | 40 |
Nominal discharge current | In(8/20μS) | 20 |
| Ressponse time | NS | <25 |
| Lndication of invalidation | Aging invalidation:green Normal,red:Invaldation | |
| Operating condition | Temp:-40℃~+70℃ | |
| RH≤95%(25℃) | ||
| Sea level elevation≤3km | ||
Remote signal function | Can also picking | |
| Remarks | Other max continuous operating voltage can be customized | |
Working principle of product
During the operation of the equipment, the lightning arrester will
play a protective role once the abnormal voltage occurs.
When the protected device is running under normal working voltage,
the arrester will not work, and it will be regarded as a circuit
for the ground. Once the high voltage is present and the insulation
of the protected equipment is endangered, the lightning arrester
acts immediately and leads the high voltage impact current to the
earth, thus limiting the amplitude of the voltage and protecting
the insulation of the electrical equipment. When the overvoltage is
gone, the arrester is restored to its original state quickly, so
that the system can supply electricity normally.
The main function of the lightning arrester is to reduce the
voltage value of the protected equipment through the action of
parallel discharge gap or nonlinear resistance, and to reduce the
voltage value of the protected equipment, so as to protect the
power equipment.
Notice of product
1. the protected equipment must have good grounding, and the
grounding impedance value is according to the relevant standard.
2. identify the input / output interface identifier of the
lightning protector, input the external line and output the
connection device.
3. it should match the working voltage of the protected equipment.
Please install according to the installation sketch.
Company profile
Thor is following the international quality system standards, is ISO 9001 certified and our technical standards are in line with GB18802.1-2011/IEC61643-1.
Two In One Single Phase Surge Protector , 420V 40KA Mains Surge Protection Devices
Inquiry Cart
0