Home Circuit Surge Protective Device Type 3 Against Lightning Fluctuations

385v home circuit surge / surge protector appliance, lightning protection 40KA.

Product introduction

Surge protector is used to protect the line from damage caused by lightning induced voltage, power interference, electrostatic discharge and so on.
The surge protector uses a multilevel protection circuit, selects the brand components, and makes use of advanced production technology. It has the characteristics of low flow residual pressure, sensitive reaction, stable performance, reliable work and so on. It is suitable for family housing, the third industry and industry.

Working principle of product

The lightning arrester can effectively protect the power equipment. Once the abnormal voltage appears, the lightning arrester will play a protective role.
When the protected device is running under normal working voltage, the arrester will not work, and it will be regarded as a circuit for the ground. Once the high voltage is present and the insulation of the protected equipment is endangered, the lightning arrester acts immediately and leads the high voltage impact current to the earth, thus limiting the amplitude of the voltage and protecting the insulation of the electrical equipment. When the overvoltage is gone, the arrester is restored to its original state quickly, so that the system can supply electricity normally.
The main function of the lightning arrester is to reduce the voltage value of the protected equipment through the action of parallel discharge gap or nonlinear resistance, and to reduce the voltage value of the protected equipment, so as to protect the power equipment.

Product Installation

With 35mm standard DIN-rail mounting, connecting copper stranded conductor is 2.5~35mm²

At front of spd each pole must be setted protection---used fuse or miniature circuit breaker lightning current SPD protection,after SPD breakdown to short circuit protection.

SPD install on protected line(equipment) to the front and connected to the supply line. A class products install in the building home-entry line hold larger surge current total distribution box. B, C class products most install on the floor distribution box, D class products close to the front-end equipment that smaller surge current, smaller residual voltage place.

Product features

1. tunnel type terminal connection, tighter wiring is more compact.

2. cut off the line when undervoltage occurs, and reset automatically after restoration.

3. Easy to install with small sizes

4. copper fittings have good electrical conductivity

Product specification

Notice of product

1. it should match the working voltage of the protected equipment. Please install according to the installation sketch.

2. lightning protector's input port (IN) is connected to the signal channel, and the output terminal (OUT) is connected with the input end of the protected device, so it can't connect with the signal.

3. when installing, pay attention to the cable entering and leaving the surge protector. The cables should be separated to avoid the two coupling of surge.

4. in order to limit the inductive coupling between the protected part after installation and the part of the unprotected equipment, we need to make some measurements. The mutual inductance can be reduced by the separation of the inductive source and the sacrificial circuit, the selection of the loop angle and the limitation of the closed loop area.

Company profile

Thor has been designing new products to meet the RoHS directive since 2006. Thor’s ongoing commitment to RoHS compliance includes continuing efforts to reduce the presence of hazardous substances in the design and manufacture of a growing number of popular products.

Ltd is committed to meeting the requirements of the European Union’s Waste Electrical and Electronic Equipment (WEEE) directive. This directive requires producers of electrical and electronic equipment to finance the take-back for re-use or recycling of their products placed on the EU market after 2005.

Thor is all about protecting against the damaging effects of power transients. It is our goal and mission to connect our customer challenges with high-quality, right-priced solutions and products – completed by unrivaled customer service and technical support.

Incorporated in 2006, Zhejiang Thor Electric Co., Ltd has built everything to offer a wide range of innovative and reliable surge protection solutions and products.

Thor is following the international quality system standards, is ISO 9001 certified and our technical standards are in line with GB18802.1-2011/IEC61643-1.

All types and classes of our lightning and surge arresters 20KA~200KA(8/20μS) and 15KA~50KA(10/350μS) are tested and pass all the requirements based on their class.

Thor has been designing new products to meet the RoHS directive since 2006. Thor’s ongoing commitment to RoHS compliance includes continuing efforts to reduce the presence of hazardous substances in the design and manufacture of a growing number of popular products.

Zhejiang Thor Electric Co., Ltd is committed to meeting the requirements of the European Union’s Waste Electrical and Electronic Equipment (WEEE) directive. This directive requires producers of electrical and electronic equipment to finance the take-back for re-use or recycling of their products placed on the EU market after 2005.