8 Inches Suction Slurry Pump , Double Casing Industrial Sludge Pump

8 Inches Suction Slurry Pump , Double Casing Industrial Sludge Pump

Main introduction of slurry pump

12/10ST- is double casing structure,double casing structure namely pump body, pump cover with replaceable wear-resistant metal lining (including impeller, sheath, sheath, etc.). 8 / 6 - R slurry pump (suction 8 inch discharge 6 inch) double pump shell pump body, pump cover according to the working pressure using gray iron or ductile iron manufacturing, vertical open, bolted connection. The pump body has a stop port connected with the bracket by bolts. The pump outlet can be rotated by eight angles. The front and rear cover plates of the impeller have back blades to reduce leakage and improve the service life of the pump.

Model meaning

8 / 6 E - R

8-------Suction diameter(Inch)

6-------Discharge diameter(Inch)

E-------Support type

------Slurry pump type

R--------Natural Rubber

Specifications

8 / 6 E - R start: Check the entire unit as follows before starting.

(1) The pump should be placed on a firm foundation to withstand the full weight of the pump to eliminate vibration and tighten all anchor bolts.
(2) Pipes and valves should be supported separately. @Slurry pump 8/6E-R There is a gasket at the pump flange. When tightening the coupling bolt, please pay attention to the pump metal lining is higher than the flange. At this time, the bolt should not be tightened too much to avoid damage to the gasket.
(3) Rotate the shaft by hand according to the direction of rotation of the pump. The shaft should be able to drive the impeller to rotate, and there should be no friction. Otherwise, the impeller clearance should be adjusted.
(4) Check the steering of the motor. Make sure that the pump rotates in the direction of the arrow marked on the pump body. Note that the pump is not allowed to rotate in the opposite direction, otherwise the impeller thread will trip, causing damage to the pump.
(5) When the transmission is directly connected, the pump shaft and the motor shaft should be accurately centered. When the belt is driven, the pump shaft and the motor shaft should be parallel, and the position of the sheave should be adjusted so as to be perpendicular to the groove to avoid severe vibration and wear.
(6) A detachable short pipe shall be installed at the suction pipe of the pump. The length shall be sufficient to disassemble the pump cover and replace the wearing parts to facilitate the inspection of the pump. The length of each pump is shown in the external dimensions of each pump.
(7) Shaft seal inspection: The pump of the auxiliary impeller shaft seal has different sealing structure. Therefore, when the oil pressure cup is equipped with oil cup, it is necessary to add grease through the oil cup. The grease is recommended to be lubricated with calcium and sodium. fat.

Typical Applications:

Ash Handling

Cyclone Feeds

Pulp and Paper

Abrasive Slurries

Coal Preparation

Mineral Processing

Aggregate Processing

Construction Design

Shaft Seal Module Design

Performance table

Shijiazhuang ShizaPump Industry Co.,Ltd. founded in 2008, is a professional industrial pump manufacturer engaged in researching slurry pump, wear and corrosion resistant materials and OEM processing.

Shizapump group covers more than 40000 square meters, the registered capital is 18 million yuan. Over the years with strong strength and people-oriented concept, we absorb a large number of high-quality management and technical talents. Existing staff is more than 220 people, of whom 30% are technicians.

Our production area covers an area of 24000 square meters, the total production capacity of an annual output is 10000 units (sets), and the annual output of all kinds of high chromium alloy castings is 2000 tons.The production area is divided into five districts one area and two centers, namely mould casting, heat treatment, fine machining, forge welding and assembly coating of five production areas; finished spare parts; quality analysis and water experiment. The main material of products: A05, A49, A33, A51 and other high chromium white cast iron.

Shijiazhuang ShizaPump Industry Co.,Ltd. fully implements the ISO9001 management system and observes the process of inspection. Quality inspection records are available in all production processes. Professional instruments include spectrometer, metallographic analyzer, flaw detector, mechanical test machine (strain, impact, hardness), magnetic flowmeter, pressure gauge, ammeter, vibration meter, noise meter, hydraulic experimental curve of professional software. Perfect detection guarantees the quality of equipment to ensure that each pumps and parts are fully in line with the requirements.

Shijiazhuang ShizaPump Industry Co.,Ltd. has spread all domestic market in China over 30 provinces and municipality. Also has been successfully used in 20 countries in global .First line staff have professional experience to provide service for customers.