Stainless Steel Bag Filter Vessel Tank With SS304 / SS316 Material For Filtration System

Stainless Steel Bag Filter Vessel Tank With SS304 / SS316 Material For Filtration System

Bag Filter Vessel replace the filter bag

1) High-efficiency filter bags are made of fine fibers, which are less hydrophilic. The surface of the fiber is not wetted by water, so like other filter

elements that use the same material, it is wetted with other liquids with a lower surface tension before use. Before installation, you must

immerse the filter bag in a pre-fluid that matches the filtered liquid for a few minutes.

2) Open the top cover of the bag filter.

3) Stabilize the top cover and carefully remove the filter bag.

4) Put in a new filter bag, please refer to the installation process.

Bag Filter Vessel Monitoring the quality of filtration

When the liquid input pressure is stable, the filtration quality is closely related to the pressure difference in the filter bag. If the pressure

difference is too large, the filter pore size of the filter bag is blocked and the filtration speed is lowered. Therefore, we recommend that when the

bag filter starts working, the pressure difference should be checked regularly, and the pressure difference displayed by the front and rear

pressure gauges should be used to determine the time to replace the filter bag. Generally, the filter bag can withstand a pressure of 0.5-

1Kg/cm2 (0.05- About 0.1Mpa), when the pressure difference reaches this range, the filter bag should be replaced in time to avoid the filter bag

from rupturing and affecting the filtration effect.

If the pressure differential drops suddenly, stop the filtration immediately and check for leaks.

Five, pressurized discharge residual liquid

When filtering high-viscosity liquids, compressed air can be introduced into the exhaust valve to accelerate the discharge of the remaining liquid

and shorten the waiting time. Its device is shown in the figure. Please note: The air used for pressurized discharge must be stable and the

pressure should not exceed the working pressure of the filter.

The steps are as follows:

1) Close the input valve.

2) Open the intake valve.

3) The gas is introduced into the bag filter, and the remaining liquid is exhausted.

4) Check the outlet pressure gauge to confirm that the gauge pressure is equal to the compressed air pressure; confirm that there is no liquid

outflow at the outlet.

5) Close the intake valve.

6) Slowly open the exhaust valve; the exhaust valve is discharged at the outlet of the exhaust valve and must be led to a safe place or filter

suction port.

7) After the compressed air is exhausted, close the exhaust valve. At this point, there should be no pressure inside the filter, and the cover can

be opened.

Bag Filter Vessel detail pictures:

Guangzhou Chunke Environmental Technology Co., Ltd. was established in 2009 is located in Guangzhou Baiyun District Junhe Street, near Guangzhou Baiyun International Airport, an independent mechanical processing, production, commissioning, testing, packaging workshop and spacious office building, the total area More than 6000 square meters.

The company has been committed to solving the drinking and industrial water treatment problems, specializing in the manufacture of desalination equipment, brackish water equipment, drinking pure water equipment, industrial water, ultra-pure water equipment and bottled water production line, the current products are exported to more than 100 countries And the region; and passed the ISO9001 international management quality system certification, the European Union CE certification, the United States Water Quality Association member units.

After years of development, the company production equipment, advanced management, a blend of water treatment and filling technology in a number of high-tech talent, in the machinery manufacturing, filtration technology, automation control, project management, bottled water plant planning A field to reach the international advanced level.

Chunke environmental technology companies adhere to the "integrity-based, technology first, the responsibility for the" business philosophy, and constantly upgrade the "Made in China" in the international competitive position. For your construction of quality assurance, leading the trend of "turnkey" project, is our unremitting efforts! With the company's development and improvement, will be better to provide comprehensive, timely, thoughtful, enthusiastic technical support and after-sales service to meet the needs of our customers. We warmly welcome customers and partners from all over the world to visit and exchange, and work together to solve the global water problem!