1000V Class II Power DC Lightning Arrester SPD Type 2 Solar PV
Surge Protection
1000V Class II Power DC Lightning Arrester SPD Description:
• BRPV series PV Surge Protective Device 40KA DC 1000V SPD suitable
for the new energy wind power generation system, its working
voltage covers 600V, 1000Vand 1500V.
• BRPV3-1000 type 2 solar PV surge arresters/SPD is designed to
protect DC powered equipment against lightning surge voltages in
photovoltaic power supply network, such as inverters, combiner
boxes and charge controllers.
• The protection flow is large, the residual pressure is very low,
and the response time is fast.
• It utilizes high energy metal oxide varistors/MOV
• Photovoltaic DC surge protector is a lightning protection product
designed for the solar photovoltaic system based on the relevant
standards.
• With the power status indication, it indicates the working state
of surge protector.
• It is installed in the main power system at DC circuit, to
protect against the indirect lighting current, direct lighting
current or other instantaneous over voltage.
• It has high lightning discharge capability, and the maximum
discharge current of each module reaches 40KA.
1000V Class II Power DC Lightning Arrester SPD Product Details:
| BRPV3 1000 |
SPD classification according to EN61643-11 | Type 2 |
SPD classification according to EN50539-11 | Class II |
Max. continuous operating dc voltage Ucpv | 1000V |
Nominal discharge current (8/20us) In | 20kA |
Max. discharge current (8/20us) Imax | 40kA |
Voltage protection level [(DC+/DC-)→PE] Up | ≤4.0kV |
Response time tA | ≤25ns |
Operating temperature range Tu | -40℃-80℃ |
Operating state / fault indication | green / red |
Cross-section area (Min.) | 4mm2 |
Cross-section area (Max.) | 35mm2 |
For mounting on | 35mm Din rail |
Enclosure material | Thermal plastic UL94-V0 |
Degree of protection | IP20 |
Order Code | B8010 |
Order code(With remote signal) | B8012 |
Technology characteristic:
1000V Class II Power DC Lightning Arrester SPD Features:
• Module design, convenient installation, with easy electric
maintains operation.
• Type 2 surge protector for photovoltaic system
• The lightning protector uses the multilevel protection circuit,
selects the brand components and uses the advanced production
technology.
• Imax - 40kA/pole (8/20 waveform)
• Ucpv - 1000V DC
• Up -4.0kV
• Built-in over current and over heat, temperature control open
circuit technology
• High energy anti-surge components MOV
• Adopt independent intelligence property right and high
performance sensitivity resistance plates
• Failure status indicator, green/red
• Small creepage current, fast response time, remnant low voltage.
• DIN rail mounting, pluggable module, convenient replacement
• With remote connection, can realize remote control.
1000V Class II Power DC Lightning Arrester SPD Use of attention:
1. Connect the grounding wire of the lightning protector to the
ground wire of the lightning protection system.
2. Surge protector is installed with 35MM standard guide rail
3. Determine the discharge current path
4. Lightning arrester must be reliably connected to the ground wire
of the lightning protection system, and the connection line is
short, thick and straight.
Working principle of product:
In the solar photovoltaic system, the inductive or capacitive
coupling voltage is caused by the lightning shock and the switching
operation of the upstream power supply system. Therefore, the surge
may damage the photovoltaic modules and inverters, which will cause
serious consequences for the operation of the photovoltaic system.
The photovoltaic lightning arrester is specially developed for this
purpose. The lightning protection module of the DC power supply,
once the high voltage, and endanger the insulation of the protected
equipment, the lightning arrester acts immediately, and the high
voltage impact current is directed to the earth, thus limiting the
amplitude of the voltage and protecting the insulation of the
equipment. When the overvoltage is gone, the arrester is restored
to its original state quickly, so as to protect the power
equipment.
Our Services:
• 17 years global leading profession manufacture of electrical
products surge arrester.
• All products will be well packed before shipping.
• Standard packaging, and you can also tell us your own
requirements on packaging.
• Faster delivery.
• Individually Tested Prior to Shipment.
Packaging & Shipping:
Company information:
Wenzhou Britec Electric Co., LTD. a Chinese professional SPD
manufacture company. Our company was established in 2003, is
China's professional produce low voltage surge arrester of
enterprises. Welcome the friends from anywhere in the world, as
long as you have about surge protection device demand, please
contact us!
Certification:
FAQ:
A: Are you an agent or a factory?
Q: We are a factory.
A: What is the port of exportation for your factory?
Q: Ningbo/Shanghai,China.
A: What’s your main market?
Q: Western Europe, Eastern Europe, northern Europe, southern
Europe, Central Europe, East Asia, South Amercia, the Middle East
and so on.
A: What’s the MOQ?
Q: Normally 200pcs.
A: Why choose us?
Q: We have rich experience in produce and professional quality
control system.
A: Can you let me how to control the quality?
Q: We have our QC team and quality control system, before
packaging, we will inspect the goods carefully. We will try our
best to make you satisfactory.
A: What’s the payment terms?
Q: 30% deposit, balance before shippment.
A: What’s the mass production lead time?
Q: Usually 20 days after receiving the customer’s deposit.
A: What the certificates do you have?
Q: TUV, CE, CB etc.