DC01 Cold Rolled Steel Sheet Coil DIN EN 10130 10209 DIN 1623
Brand Name:Baosteel, RAYIWELL MFG
Certification:DIN EN 10130 10209 DIN 1623
Model Number:DC01,SPCC
Minimum Order Quantity:25ton
Delivery Time:35DAYS
Payment Terms:L/C, T/T
Contact Now
Add to Cart
Site Member
Location:
Suzhou Anhui China
Address:
1-506,Xingzheng Road,Longcheng Town,Xiaoxian,Suzhou,Anhui,China
Supplier`s last login times:
within 27 hours
Product Details
Company Profile
Product Details
COLD ROLLED STEEL SHEET AND COIL – (DC01 BS EN 10130:2006)
Cold rolled steel, (often referred to as Cold reduced or CR), is a low carbon product, produced using raw material such as coke and coal at steel mills through out the world.
DC01 steel (1.0330 material) is a European standard cold-rolled quality low-carbon steel flat product for cold forming. … In addition, this steel is also used under electrogalvanizing conditions. The designation of the steel is DC01+ZE (or 1.0330+ZE), and the standard is EN 10152
Cold rolled steel according DIN EN 10130, 10209 and DIN 1623
One of the leading Mild Steel Strip suppliers in the China, supplying DC01 to DIN EN 10139, Cold rolled uncoated Mild Steel Strip for cold forming, BS 1449 CS1, DC03 to DIN EN 10139, Cold rolled uncoated Mild Steel Strip for cold forming, BS 1449 CS1/CS3 and DC06 to DIN EN 10139, Cold rolled uncoated Mild Steel Strip for cold forming, BS 1449 CS4
One of the leading Mild Steel Strip suppliers in the China, supplying DC01 to DIN EN 10139, Cold rolled uncoated Mild Steel Strip for cold forming, BS 1449 CS1, DC03 to DIN EN 10139, Cold rolled uncoated Mild Steel Strip for cold forming, BS 1449 CS1/CS3 and DC06 to DIN EN 10139, Cold rolled uncoated Mild Steel Strip for cold forming, BS 1449 CS4
Technical data
Cold rolled steel according DIN EN 10130, 10209 and DIN 1623
Cold rolled steel is also part of our product portfolio. Cold rolled steel is excellent for cold forming. This product group assigned the grades DC01 to DC07, DC01EK to DC06EK, DC03ED to DC06ED and S215G to S325G.
The grades are classified according to the maximum permissible
yield strength and can be subdivided as follows.
DC01 – This grade can be used for simple forming work, for example
Bending, embossing, beading and pulling are used.
DC03 – This grade is suitable for forming requirements such as Deep
drawing and difficult profiles suitable.
DC04 – This quality is suitable for high deformation requirements.
DC05 – This thermoforming grade is suitable for higher forming
requirements.
DC06 – This special deep drawing quality is suitable for the
highest deformation requirements.
DC07 – This super deep drawing quality is suitable for extreme
deformation requirements.
Enamelled grades
The steel grades DC01EK, DC04EK and DC06EK are suitable for
conventional single-layer or double-layer enamelling.
The steel grades DC06ED, DE04ED and DC06ED are suitable for direct enamelling as well as for enamelling according to the two-layer / one-firing method and for special applications of two-layer enamelling for low-distortion enamelling.
Surface type
Surface A
Mistakes such as pores, small grooves, small warts, slight
scratches and a slight discoloration that does not affect the
ability to reshape and adhere to surface coatings are permitted.
Surface B
The better side must be free from defects so that the homogeneous
appearance of a quality finish or an electrolytically applied
coating is not impaired. The other side must at least meet the
requirements of surface type A.
Surface finish
The surface finish may be particularly smooth, dull or rough. If no
details are given when ordering, the surface finish will be
delivered in a matt finish. The four surface finishes listed
correspond to the center roughness values in the following table
and must be tested in accordance with EN 10049.
DC01 Cold Rolled Steel Sheet Coil DIN EN 10130 10209 DIN 1623
Inquiry Cart
0