60V 2000A High Frequency Switch Power Supply For Hard Chrome Plating

60V 2000A high frequency switch power supply for hard chrome plating

During the oxidation process, the workpiece continuously generates gas, hindering the continued oxidation, making the oxide film loose and porous, and the intermittent high and low current conversion rectifier of the pulse power rectifier works, which is conducive to the precipitation of gas, easy to form a film, the film thickness increases, the oxide film It is denser, and its hardness, thickness and color are greatly improved. At present, the commonly used oxidation power supply is a DC power supply, and its output has no pulse, so the output generated is relatively loose, and the thickness, hardness, and color of the oxide film cannot reach the effect of pulse oxidation rectifier;
Superior performance of hard oxide pulse rectifier:

1-32 minutes adjustable soft start time, and can be used as a pulse soft start, especially suitable for hard oxidation process;
1-256 minutes running time is adjustable (independent of soft start time), automatic shutdown;
Multiple working options: pure pulse, pulse superposition, DC, etc .;
During the operation, it can display all operating parameters at any pulse frequency, duty cycle, pulse-based high & peak value, so that you can fully control what workpiece is in the end;
Under operating conditions, the parameters can be freely modified, adjusted, and stored at any time. After the power is turned off, the time is saved for 35 years. The stored parameters will be automatically run at the next startup;
According to the anodizing characteristics of aluminum and titanium, the working method is current stabilization and voltage limiting work to ensure sustainable and efficient oxidation. With the extended power bath of electrical solutions, the thickness of the oxide film increases if the output voltage rises to safety In the set value tree, the voltage stops rising, and crent gradually decreases, which really protects the workpiece from melting;
Perfect safety guarantee measures, with a variety of intelligent fault protection, over current, fault phase, phase sequence error, short circuit;
The transformer coil winding and bus bar are made of high-quality copper (copper content 99.99%), with good conductivity and high current efficiency;
The transformer coil adopts double vacuum impregnation process, which has good insulation and corrosion resistance.
Specification

Pulse rectification parameters:
Input voltage: three-phase four-wire 380V, 415V, 50-60HZ;
Output current: 200-10000A optional;
Output voltage: 40V, 60V, 70V, 90V, 110V, 120V optional;
Pulse frequency: 0.4 -25 Hz;
Duty cycle: 10% -90%;
Output waveform: pulse, pulse superposition, DC;
Running time: 1-256 minutes adjustable;
Working mode: steady current and pressure limit;
Cooling: forced air;
Load operation: 24 hours full load operation, such as 1000 meters above sea level to reduce the use capacity;
Working environment temperature 0 ℃ -40 ℃;
The relative humidity is less than 90% (ambient temperature 20 ℃ ± 5 ℃).

Pulse type hard oxidation power supply
1 Pulsed oxidation power supply is used to produce aluminum products with a film thickness of more than 20μ, which can be quickly

coated and save energy.

2. The output pulse frequency and duty cycle are precisely adjustable, and the number of positive and negative pulses can be flexibly

configured.

3. Accurate constant current and constant voltage output characteristics, the control accuracy is within ± 0.5V and ± 0.5A respectively.

Support two working modes: program control and manual. In program control mode, users can perform constant current / constant voltage

output characteristics, running time, pulse frequency, duty cycle, positive / negative pulse number, positive / negative pulse current, positive /

negative pulse voltage for up to 4 working stages Programming separately, the working process is fully automated. This mode is particularly

suitable for mass industrial production of stereotyped products.

Chengdu Xingtongli Power Supply Equipment Co., Ltd. was set up in 1995. We are a high technology company dedicating to the design and manufacture of switched-mode power supply. We are experienced in the field of power electronics, energy transforming technology and industry control system. The performance of switching power supply we designed is excellent. It is safe, green and reliable. With these advantages, our products are widely used in aerospace, military industry, railway transportation, electric power industry, automobile manufacturing, shipbuilding, petroleum industry and some other industries. Now we have already held a big market share of the power supply in metal surface finishing field. We are one of the main vendors of electroplating power supply in China.

We are making great efforts to develop new products to meet different requirements. Adhering to the business principle of mutual benefits, we have built up a good reputation among our customers due to our perfect services, quality products and competitive prices. We warmly welcome customers from at home and abroad to cooperate with us for common success.

We warmly welcome customers from at home and abroad to cooperate with us for common success.