DS1230Y-150+ 256k Nonvolatile SRAM SS Replaces RAM Module IC

DS1230Y-150+ 256k Nonvolatile SRAM SS Replaces RAM Module IC

FEATURES

10 years minimum data retention in the absence of external power

Data is automatically protected during power loss

Replaces 32k x 8 volatile static RAM, EEPROM or Flash memory

Unlimited write cycles

Low-power CMOS

Read and write access times as fast as 70 ns

Lithium energy source is electrically disconnected to retain freshness until power is applied for the first time

Full ±10% VCC operating range (DS1230Y)

Optional ±5% VCC operating range (DS1230AB)

Optional industrial temperature range of -40°C to +85°C, designated IND

JEDEC standard 28-pin DIP package

New PowerCap Module (PCM) package

- Directly surface-mountable module

- Replaceable snap

-on PowerCap provides lithium backup battery

- Standardized pinout for all nonvolatile SRAM products

- Detachment feature on PowerCap allows easy removal using a regular screwdriver

PIN DESCRIPTION

A0 - A14 - Address Inputs

DQ0 - DQ7 - Data In/Data Out

CE - Chip Enable

WE - Write Enable

OE - Output Enable

VCC - Power (+5V)

GND - Ground

NC - No Connect

DESCRIPTION

The DS1230 256k Nonvolatile SRAMs are 262,144-bit, fully static, nonvolatile SRAMs organized as 32,768 words by 8 bits.

Each NV SRAM has a self-contained lithium energy source and control circuitry which constantly monitors VCC for an out-of-tolerance condition.

When such a condition occurs, the lithium energy source is automatically switched on and write protection is unconditionally enabled to prevent data corruption.

DIP-package DS1230 devices can be used in place of existing 32k x 8 static RAMs directly conforming to the popular bytewide 28-pin DIP standard.

The DIP devices also match the pinout of 28256 EEPROMs, allowing direct substitution while enhancing performance. DS1230 devices in the Low Profile Module package are specifically designed for surface-mount applications.

There is no limit on the number of write cycles that can be executed and no additional support circuitry is required for microprocessor interfacing.

READ MODE

The DS1230 devices execute a read cycle whenever WE (Write Enable) is inactive (high) and CE (Chip Enable) and OE (Output Enable) are active (low).

The unique address specified by the 15 address inputs (A0 - A14) defines which of the 32,768 bytes of data is to be accessed. Valid data will be available to the eight data output drivers within tACC (Access Time) after the last address input signal is stable, providing that CE and OE (Output Enable) access times are also satisfied.

If OE and CE access times are not satisfied, then data access must be measured from the later-occurring signal (CE or OE ) and the limiting parameter is either tCO for CE or tOE for OE rather than address access.

WRITE MODE

The DS1230 devices execute a write cycle whenever the WE and CE signals are active (low) after address inputs are stable. The later-occurring falling edge of CE or WE will determine the start of the write cycle.

The write cycle is terminated by the earlier rising edge of CE or WE . All address inputs must be kept valid throughout the write cycle.

WE must return to the high state for a minimum recovery time (tWR) before another cycle can be initiated. The OE control signal should be kept inactive (high) during write cycles to avoid bus contention.

However, if the output drivers are enabled ( CE and OE active) then WE will disable the outputs in tODW from its falling edge.

King--- Originator of ANTERWELL, engaged in the IC electronics industry in 1998 and establish ANTERWELL in 2004. The company is located in Shenzhen Huaqiang North, the largest electronic center in Asia. Our main business is the technical development and electronic products import and export business. Currently, we have branches in Hong Kong and Malaysia.

Up to now. ANTERWELL have more than 1,000,000 types of electronic components in stock. ANTERWELL has become one of the top choices for purchasing IC chips both domestically and internationally. King is a senior IC chip expert, sales engineer, and mentor, leading an elite team with customer first, quality first, honesty, trustworthiness, and mutual benefit. We look forward to cooperate with you to create a better future!

ANTERWELL’s main products include semiconductors, resistors, capacitors, diodes, inductors, connectors, transistors, sensors, etc. Involving the major well-known brands such like: TI, XILINX, FAIRCHILD, STM, MICRON, MICROCHIP, TDK, SAMSUNG, ON, NXP,IR,ADI, ATMEL,VISHAY,LINEAR etc.

ANTERWELL adheres to the development concept and purpose of "direct stock offer, excellent quality, favorable price, and sincere service", which is deeply recognized by domestic and foreign customers. Based on the long-term development goal, ANTERWELL provides customers with standardized, professional, and diversified high-quality services through a strong market service network. ANTEWRELL has multiple skilled and capable executives with a professional QC team and excellent sales team to win the high support and trust of the vast customer base! We provide the best quality, price and service.

ANTERWELL will be your best Partner.