Double Cross Arm Round 69kv 10m joint type Steel Utility Pole Explosion - proof

Round 69kv 10m 3mm thickness joint type Steel Utility Pole for Electrical Distribution With double cross arm

Specifications:

Production Control

10 Reasons That Steel Poles Make Sense According to research, here are the primary reasons wooden and concrete utilities are switching to Steel Utility Pole:

o Easy to Handle
o Light Weight
o Long Life
o Cost Effective
o Low Maintenance
o Sustainable
o Durable
o Safe
o Aesthetics
o Engineered for Strength

Application:

Transmission Applications
Light Duty Steel Poles
Custom Design Transmission Poles
Steel H-Frame Poles

Substation Applications
Dead End Structures
A-Frames and H-Frames
Special Application Structures
Low Side Supports – Buss, Switch, and Other equipment
Static and Shield Wire Poles

Design:

Standard Accessory
-Top plate
-Base plate
-Bottom strip
-Standard hole
-Climbing rung
-Anchor bolt
-Bitumen protection
-Painted marking
-Removable ladder

Available Foundation Types
Direct Embedment
Anchor Bolt/Base Plate
Vibratory Steel Caisson

Available Finishes
Galvanized per ASTM A123
Paint over galvanized,paint over black steel
Powder Coating

Standard Features

In-Ground Mounted:
12-sided pole shaft
Welded top cap
Mounting holes (to your specification if required)
Identification plate
M12 earth point 250mm above the nominal ground line
M24 nut 250mm above the nominal ground line (to assist lifting)
Additional in-ground corrosion protection 200mm above to 400mm below the nominal ground line
Anti-sink straps
Hot dip galvanised finish

Base Plate Mounted:
12-sided pole shaft (40kN to 80kN)
16-sided pole shaft (100kN & 120kN)
Welded top cap
Mounting holes (to your specification if required)
Identification plate
M12 earth point 250mm above the pole base
Two lifting gussets on the base plate
Anchor bolts, templates, nuts & washers
Hot dip galvanised finish

Transmission Structures

Steel Tapered Poles for Transmission Structures

H-frames Power Pole DesignsVariety of Finishes for and Utility Pole Structures

Smaller Diameter Light Steel Structures (Sidewalks and Tight Right-of-Ways)

Custom Design Matching to Wood Pole Classifications

Custom Pole Designs

Wood equivalent Steel Power Pole Configuration for Short Lead Times or Repair Jobs

Antenna Tower Structures

Patented Splice Joints for Steel Structures

Traditional Flange Splices for Steel Structures

Cell Tower Structures

Lattice Design Structures

I-Beam Structures

Pre-Drilled Power Pole Apparatus Using Plasma Burning Process

Self-Conducting Stainless Steel Utility Poles for Grounding Purposes

Hardware for Light Poles

Pre-drilled Holes for Safety Steps and Equipment

No Extra Welding is Needed for Conductor Hookups to Attach Transmission Lines

Single Circuit Line Hookup for Utility Pole Structures

Double Circuit Line Hookup for Utility Pole Structures

Shield Wire Guards to Protect Against Lightning

Substation Structures

Tapered Tubular Substation Structures

Steel Substation Structures

Custom Substation Designs

Closed Section Tubes

I-Beam Structures

Lattice Structures

Steel Structures with Higher Translational Stiffness

Low Profile Aesthetically Pleasing Structures

Higher Terminal-Stop/Take Off Angles

Higher Tension Wires Due to Design

Substation Structures Exceed Wood Pole Standards

Estbilsed in 1989,Jiangsu Milky Way Steel Poles is located in Wuxi,East of China ,near one of the largest sea port of China ,Shanghai,Port .

Our Products have been widely used in the power transmsion ,signal transmission and ligting for street ,road ,square ,palaestra.and so on

We have plenty of export experience . Since our first overseas order from Pakstan in 1991 of 132 KV transmission poels ,our products have been deliveried to more than 70 contries and areas ,including America,Australia ,Russia ,Genmery ,Span,Philippines ,Malaysia and so on

To assure our products qualified ,we take steps as follows :

1. Management team : We have employ the foreign export to take chaege of the overall managemnt ,especailly the technical managemnt and quality management .

2. Introducing ISO management ,We are awared ISO 9001:2008 certificate . .

3. Lofting and design software :We have transmisson power pole design software which can help us design all kinds of steel pole ,at the same time ,the TMA and LMA are adopted by us to provide the design the drawing accuratly .

4. QC Inpection:It is our company policy that all the finish product should be inspected by our specialzed QC in every manufacure steps and beofore every shipment .

We are always persisting in horzontal cooperation with domestic senior project institute and technical colleges .The enterprise also has an highly qualified team working at R&D ,manufacure ,QC ,aftersales service and other important positions .