Remote Control 4 Channel Vehicle DVR Camera System H.264 Wifi Gps Tracker

Remote Control 4 Channel Vehicle DVR Camera System H.264 Wifi Gps Tracker

Performance Parameters:

Functional Features:

If the switch is set, the positive and negative electrodes need to be directly connected to the battery, and the ignition signal is cut off. (If you set the timing, you need to keep the machine powered)

note:
1. Use a DC power supply for the recorder. When connecting the power supply, pay attention to the positive and negative polarity of the power supply.
2. The recording input voltage range is 10-36V. Do not connect the power supply beyond this range. Too low a voltage will cause the VCR to not work properly, and high voltage will damage the VCR.
3. It is recommended to connect the recorder directly to the battery power output of the car. Please note that do not pick up the power output of the generator on the vehicle, because the generator may generate instantaneous high voltage during startup and damage the recorder.
4. After the video camera is connected to the camera, the startup power exceeds 30 watts (power consumption varies depending on the external device). The power supply must be able to provide more than 30 watts of power.
5. All power connections to the recorder must be sufficiently thick to withstand more than 60 watts of power. (For example, when the onboard power supply output voltage is 12V, the power cord must be able to withstand more than 5 amps of current)
6. It is recommended to wear a wear-resistant, heat-resistant, waterproof, and oil-resistant casing on the outside of the power cord. Because of long-term vibration on the vehicle, it can cause short circuit or open circuit due to friction.
7. The power cord is located near the positive end of the power output on the vehicle. A 10 amp fuse box is required. In case of a short circuit in the power line, the power on the car will be burned.

Q: What should I do when the product has problems that I cannot handle?
A: Record product model and software version number, submit detailed problem description to our technical support engineer for analysis.
The more detailed you describe, the more convenient our analysis will be.

Q: What if the car host device does not have video output?
A: 1. Check the boot status of the host. Check the device input power, check the power line wiring is correct, whether the ground wire back to the battery, the power line insurance is intact; at the same time check the host power supply red and yellow line is normal, if only one line power supply, then the host Can't start it.
2. Check if the display is powered and if the display video switches to AV and the corresponding channel status.
3. Check the connection status of the host video output cable and the monitor.

Q: The host is always restarted
A:1. Check if the voltage of the device is insufficient and the starting voltage of the device has not been reached, causing the device to restart;
2. If the hard disk or SD card is faulty, the device may not start up. Remove the storage device and turn it on again to determine whether the storage device is faulty.

Q: What should I do when the host's video input interface and camera input interface are different?
A: The car host uses a 4-pin connector and the camera is a BNC connector or aerial head. If they are not the same, use an adapter to connect, or define a standard docking line with the vehicle host sequence.

Q: The device is turned on, and the hard disk is also installed, but what should I do if it is not recorded?
A: 1. Check if the HDD/SD is formatted after installation. Unformatted HDD/SD cannot be used. Go to Main Menu - System Settings - Format to format the newly installed HDD/SD.
2. Whether the recording channel is closed or not, whether the scheduled recording is set, and no recording is performed within the recording period.
3. Check that the hard disk is in good contact and the front panel HDD/SD lamp is lit.

Q: The video file is missing, or there is no video file in a certain period of time?
A:1. By determining the time period determined in the first video file after the final video file is lost and restored.
2. Confirm whether the host has not booted during that period of time. For example, the host that stops parking, loading, unloading, etc. does not set a time-lapse recording.

GPS related issues
Q: GPS module exists but no coordinate information?
A: 1. Check if the GPS module is present.
2. Confirm whether the GPS antenna contact is good and whether the antenna is disconnected. It is recommended to place it in a place where the signal is strong.
Vehicle glass shielding will block the GPS signal.
3. If it is tested in the room, the GPS antenna is in the room and the signal is shielded. It is recommended to place the GPS antenna outdoors.
4. The impact of the surrounding environment such as trees, tunnels, driving around high buildings and elevated roads, thunderstorms, etc., may result in no signal of GPS, or receive a wrong signal.

Q: Is there a difference in GPS location on the map?
A: If the GPS module has been located, it means that the signal is valid. There are many reasons for the problem of deviation. Government restrictions, error tolerances, GPS signal interruptions, etc.; actual satellite maps may deviate due to safety considerations. General maps can be solved using GPS calibration. problem.

Other related issues
Q: Some channels have a black screen?
A: The black screen of certain channels is found on the monitor screen. The possible causes are as follows:
There is no video connection on this channel; the camera connected to this channel is damaged or abnormally working; if the power of the camera is taken from the device, the voltage provided by the device may be insufficient; the cable connecting this channel is not in good contact or damaged;

Q: Can't play back video files when playing back on a PC?
A: The possible causes are as follows: No video file path or video file is selected. Please select the path of the video file before playback; the local video file is corrupted, resulting in unreadable;

Q: Can't remote control be remote?
A: The possible causes are as follows: The remote controller is not equipped with a battery; the remote controller is damaged; the device is malfunctioning;

Q: What is the video coverage when SD card and HD video are recorded?
A: The SD card and the hard disk are each cycled. When the SD card and the hard disk are full, the original video in the respective disk is deleted.

Applications:

1. Vehicle,Truck,Bus,School Bus,etc.
2. Real-time video monitoring.
3. GPS tracking.
4. Assets Tracking.
5. Fleet Management.

Gurantee:

1. our product is free to use the Tracking service server in 24 hours each day

2. our product there is a 2 year quanlity assurance.

3. Sample fee will be returned.

Product Configuration:

1. Standard configuration

1. Device host 1
2. Power Cables 1
3. I/O Cables 1
4. AV Cables 1
5. Remote control 1
6. 3G/4G Antenna 1
7. GPS Antenna 1
8. CD( User manual) 1

2. Optional configuration:

1. camera
2. lcd display
3. SD card
4. hard disc
5. fuel sensor
6. temperature sensor

shenzhen CarTracker Technology Co., Ltd was founded in 2009,it is one of the most professional manufacturers for gps tracker and mobile DVR product.Our company is located in Shenzhen city,Guangdong province,China.At present our GPS Tracker products are mainly exported to Southeast Asia,Africa,South America,The Middle East ,Europe and so on.

Our main products are Car GPS Tracker,Personal GPS Tracker,large battery GPS Tracker and 3G mobile DVR.Every year we develop new products to meet customer requirements.and they are certified by CE,ROHS,FCC and 3C certification bodies.

We have a Research and Development team of more than twenty engineers. Most of them have a master's degree and 12 engineers have more than 8 years work experience in the GPS Industry.we also have a group of professional sales and after sales team. they will provide after-sales and pre-sales technical support for you.

Our factory is located in Cuishan industrial area,we have about 2000 square meters of building area and more 200 production staff.they are mainly responsible for gps product production,testing and quality control.our monthly output is more 20000pieces.the factory has passed ISO9001,ISO14000 Certification.

Welcome to visit our factory and we look forward to the opportunity to cooperate.