Surgical Instrument Medical Washer Disinfector With Automatic Glass Doors

Specifications :

﹒master carton dimension:

(H*W*D mm):2060X750X700;

﹒Chamber dimension:

750x700x700(mm)(LxWxH)

﹒Chamber capacity: 360 L

Weight: 250 KGS

﹒Instruments trolley: 5 layers/600x570x570(mm)(LxWxH)

﹒Basket dimension: 480x250x60 mm

﹒Body material:304 s.s material, heat and nosie insulation

﹒Chamber material: 316 stainless steel

﹒Power: 3 phasex380V/ 1 phase x 220V/50Hz

﹒Power: AC 380V 50Hz 17KW

﹒Thermal disinfection tem: ambient tem~98℃

﹒Water pressure: 0.10Mpa~0.80Mpa

﹒Water flow: 25L/min

﹒Water consumption: 15L/phrase

﹒Water tem increase: around 10.5℃/min

﹒Environment: humidity: 31℃＜80% Room tem: 5~40℃

﹒Noise: ≤60 dB

Working process:

Step 1 Pre-rinse The chamber is filled with cold water from the prefilled process tank in 15 seconds via a big quick-opening membrane valve. The speed-controlled circulation pump is soft-started and runs at full speed for superior cleaning results. The water goes via the spray manifold into the two spray arms in the top and bottom and into the spray arms of the wash carts. The chamber is drained in 15 seconds via another big quick-opening membrane valve in the conical bottom. The water is then rapidly drained into a drain tank, from where it is pumped to the building’s wastewater system.

Step 2 Wash Cold or hot water from the prefilled process tank is “dumped” into the chamber at the same time as the drain tank is being emptied. The speed-controlled circulation pump is soft-started and runs at full speed for superior cleaning results. Cleaning continues until the wash solution has operated at the set temperature for the programmed time. The chamber is then drained in the same way as in Step 1.

Step 3: Rinsing / Final Rinsing / Disinfection For the rinse phases, hot water from the pre-filled process tank is “dumped” into the chamber at the same time as the drain tank is being emptied. The speed-controlled circulation pump runs at half speed thus reducing the water consumption by up to 20%. In the disinfection phase, fresh 90°C water from the booster tank (pumped up to the process tank during the previous phase) is “dumped” into the chamber. The rinse/disinfection temperature and duration can be set to comply with all known norms. The chamber is drained as described before.

Step 4: Drying Fresh ambient air is preheated by the exhaust air in the air-to-air heat exchanger before being electrically heated to the drying temperature. The heated air is then transported in stainless steel pipes to the water manifold pipe and then into all spray arms. This concept assures up to 40% shorter drying times thanks to very turbulent and efficient drying conditions in the entire chamber. The system is also available with an optional drying sensor to abort the drying process when the preset outgoing air humidity has been reached. This means even shorter drying times when operating at part loads.

Feature:

• Ergonomic design of the door level height allows the user a convenient loading/unloading job with the support of a manual trolley or automatic loading/unloading conveyors.
• Automatic motorised verticle sliding door made of HST tempered glass (high shock tested) tempered glass with safety device.
• HEPA filtered H14 forced air drying system with adjustable time and temperature settings.
• Washing and DI disinfection temperature are fully adjustable up to 93°C
• Temperature is monitored by two independent sensors.
• 2 powerful vertically installed washing pumps that ensure high flow rate combined with effective spray pressure and also grant a complete drain of the washing circuit.
• Washing/drying cart injection system.
• Washing cart automatic identification.
• Inner cabinet, washing arms and tank filters made of high quality AISI 304 stainless steel. External cabinet made of AISI 304 stainless steel.
• Triple water filtering system captures residue preventing re-circulation and extending the pump life.
• Three standard automatic liquid dispensers provided with flow meter and level control.
• Possibility to store up to four 10 lt. containers under the chamber.

MEDPHARM Company team is committed to providing quality sterilization products, service, parts and

maintenance training at significant savings. From customized parts packages to turnkey equipment

acquisition and installation, our innovative sterilization solutions are designed to meet our customers' needs.

We understand that untimely breakdowns are costly and can be detrimental to your everyday operations.

Our service team is compromised of expert technicians that respond quickly to all of your service needs.

We offer on-site service support including inservices, installation and deinstallation of your equipment. From

breakdown repairs to comprehensive maintenance programs, we have an innovative service solution for you.

We will service on-Site Repairs.Our staff is equipped with the resources required to provide you with

on-site, on-time repairs in compliance with manufacturer specifications. We also provide installation,

deinstallation, and inservices on most makes and models of sterilization equipment. Near or far we can

provide you with service support that you need.

Our reconditioning background has taught us of the importance of having quality parts on hand at all times. We have a large inventory of individual repair parts, as well as preventive maintenance kits, and consumables in stock and ready to ship today.

With our expert technical support staff, it is not always necessary to have part numbers to place an order.

We will help you identify the quality parts that you need.