

Add to Cart
About PVC Compounds:
Cable PVC compounds are thermoplastic materials derived from
processing polyvinylchloride compositions, produced as granules.
Various properties are imparted to compounds depending on
applications and item operation conditions. This is achieved by
using plasticizers, stabilizers and modifiers in various
combinations in compositions.
PVC based plasticizers have considerable mechanical strength and
water resistance, high thermal resistance to low temperatures, good
insulation properties, insoluble in gasoline and kerosene,
abrasion, acid and alkali resistant. PVC based compounds are
readily welded and glued.
Cable PVC compounds are use in the cable and conductor industry for
manufacture of insulation and protective wire and cable sheaths.
The main final consumers of the PVC based cable and conductor
products are energy and construction industries.
Technical Data:
Items | Unit | Typical Value | Testing Method | ||
70 ℃ PVC Cable Compound | 105 ℃ PVC Cable Compound | 105 ℃ Irradiated crosslinked FR PVC Compound | |||
Tensile Strength | Mpa | 11 | 11 | 12 | GB/T 1040.3-2006 |
Elongation at Break | % | 180 | 180 | 180 | |
Heat Aging | |||||
Testing Termperature | ℃ | 100 | 135 | 135 | GB/T 8815-2008 |
Testing Time | h | 168 | 168 | 168 | |
Variation at tensile strength | % | 20 | 20 | 20 | |
Variation at elongation | % | -15 | -15 | -15 | |
Low Temperature Brittleness | ℃ | -20 | -20 | -20 | GB/T 5470-2008 |
Oxygen Index | / | ≥23 | ≥23 | ≥28 | GB/T 2406.2-2008 |
Density | g/cm3 | 1.42 | 1.42 | 1.42 | GB/T 1033.1-2008 |
Hardness | Shore A | 70-96 | 70-96 | 70-96 | GB/T 2411-2008 |
1.Technical Specifications
Test | Unit | Standard | |||
Test Method is as per BS 7655-4.2:2000 | |||||
Properties in the state as manufactured | |||||
Tensile Strength | N/mm2 | minimum | 12.5 | ||
Elongation at Break | % | minimum | 150 | ||
Properties After Aging in air oven | |||||
Ageing conditions | |||||
Temperature | ℃ | 100±2 | |||
Duration | h | 7*24 | |||
Tensile Strength | N/mm2 | minimum | 12.5 | ||
Variation | % | maximum | 25 | ||
Elongation at Break | % | minimum | 150 | ||
Variation | % | maximum | 25 | ||
Bending Test at Low Temperature | |||||
Test Conditions | |||||
Temperature | ℃ | -15±2 | |||
Results to obtained | No Cracks | ||||
Elongation Test at Low Temperature | |||||
Test Conditions | |||||
Temperature | ℃ | -15±2 | |||
Results to obtained | |||||
Elongation without break | minimum | 20 | |||
Impact Test at Low Temperature | |||||
Temperature | ℃ | -15±2 | |||
Requirement | No Cracks | ||||
Pressure Test at High Temperature | |||||
Test Conditions | |||||
Temperature | ℃ | 90±2 | |||
Results to obtained for Depth of Indentation | % | maximum | 50 | ||
Resistance to cracking | |||||
Temperature | ℃ | 150±2 | |||
Requirement | No Cracks | ||||
Loss of Mass | |||||
Ageing conditions | |||||
Temperature | ℃ | 100±2 | |||
Duration | h | 7*24 | |||
Value to be obtained for | |||||
Loss of Mass | mg/cm2 | maximum | 1.5 | ||
Hot Deformation Test(Only for specified radial thickness less than 0.4mm) | |||||
(As per BS 6469-99.1,clause10) | |||||
Deformation | maximum | 40 | |||
Insulation Resistance Constant | |||||
(As per BS 6469-99.2,clause8) | |||||
Temperature | 20±2 | ||||
K Value | 0.0035 |
2.Use and standard: Electric power Cable& Power Cablewire and cable
3.Process: extrusion
4.Appearance: cylindrical particles, plastication should be good, the color and luster is even, without obvious impurity.
5.color: Any colors, base on requirement.
Black and white, gre for Shealthing PVC compound
Red, Yellow, Blue, White and black for Insulation PVC compound
Factory Introduction:
Our factory is located in Shangyou industrial zone, Shangyou
country,Ganzhou city,Jiangxi province, and setting up sales office
and warehouse in Dongguan city. The new and standard factory is
built on 40,000 sq. mtr with a total annual capacity of
approximately 10,000 tons of various products,covers 2 flame
retardant production-line, 7 cable filler yarn production-line,32
twisted machine, with full modernization of testing equipment. All
of the products can be exported freely.
The company has passed the ISO 9001:2008 quality system
certification. Each of these products can reach to environmental
requirement by SGS company: such as ROHS, REACH-SVHC, Halogen Free.
More than 30% of products are exported to Europe, America, Japan,
Southeast Asia and Africa, having cooperation with many well-known
listed companies at home and abroad.
We always sincerely welcome any domestic and overseas customers
with great enthusiasm.
How To order :
1. Let me know the models, specification, quantities, colors you
want to order
2. We will email you the Proforma Invoice based on your order
information
3. Kindly check the PI, everything is ok, we will start production
as soon as receiving payment deposit or LC, then
deliver the goods on request, original documents will be send against full payment
FAQ:
Are you manufacturer or trading company?
We are a professional manufacturer with our own factory. And we
have the experience in producing ropes for over 30 years.
Should I pay extra fee for logo printing?
Accoring to your logo easy or complex.
If I have my thoughts,could you produce the products accoring to my
concept?
Yes,we have the professional design team to make it.
How long to make a new sample?
5-20 days which is depend on the samples' complexity
how long can i get the sample
If we have the stock,it needs 3-10 days after confirmed
If we don't have the sotck,it needs 15-25 days.
What's your sample policy?
If we have the stock,we'll send the samples for free. But the
express fee will be charged from you.