Menu code	Parameter Scale	Parameter name	Default	Unit	Remark
H00-00	25-95	Open speed adjustment	40		Corresponding PWM duty cycle 25%-95%, step size is 1
H00-01	25-95	Close speed adjustment	40		Corresponding PWM duty cycle 25%-95%, step size is 1
H00-02	5-40	Open in place decelerate angle	35		The larger the angle value, the less likely it is to shake the arm when it is in place.
H00-03	5-40	Close in place decelerate angle	35		The larger the angle value, the less likely it is to shake the arm when it is in place.
H00-04	1-20	Open accelerate adjustment	1	ms	The smaller the number, the faster the speed
H00-05	1-20	Close accelerate adjustment	8	ms	The smaller the number, the faster the speed
H00-06	1-30	Open in place angle	1	degree	step size is 1, when big than 11, will automatically check one side
H00-07	1-30	Close in place angle	1	degree	step size is 1
H00-08	7-13	Auto reverse force adjustment	10	A	step size is 1
H00-09	0-90	Delay closing adjustment	0	second	step size is 100；0 is not closing automatically,Other value will be closing automatically; This parameter is for the situation that there is no loop detector signals and non-automatic operation occasions
H00-10	10-50	Self-check speed adjustment	30		Corresponding PWM duty cycle 10%-50%, step size is 1
H00-11	0-2	Self-check mode	0		0:no operate automatically；1:operate automatically, eliminate after power off；2:operate automatically,Power failure memory.3.intelligent automatically operation.
H00-12	0-5	Self-lock force adjustment	0		0:Invalid , 1or 2 valid
H00-13	1-20	Motor deceleration time when paused	5		The larger the setting, the longer the pause time will take
H00-14	0-1	Bid-direction setting	0		0:Closing,1:opening
H00-15	0-2	Energy saving closing arm direction	0		0:invalid 1:close arm valid(energy saving voltage is determined by 49 items ) 2:open arm valid
H00-16	1-32	RS485communication address	1		Up to 32 slaves can be connected
H00-17	0-2	RS485communication rate	0		0:9600,1:19200,2:38400；Change the parameter and will be valid after power on again.
H00-18	0-2	Whether to self-check when power on	1		0:no self-check,1:self-check；2:self-check with remote control;
H00-19	0-3	self-check setting	2		0:Manually invalid,1:Keyboard SET button,2:remote control valid,3,Keyboard SET button and remote control both valid
H00-20	0-15	Monitoring parameter setting index	7		0	0XD000	Rotate speed	0~2500
					1	0XD001	Motor feedback angle	0~90 degree
					2	0XD002	Busbar voltage(V)	0~40.0
					3	0XD003	Current output
					4	0XD004	Hall state	0~7
					5	0XD005	Commutation number
					6	0XD006	Total number of trips
					7	0XD007	Run time(ms)	0~9000
					8	0XD008	Cumulative running times	0`99999999
					9	0xD00A	Time of automation operation	0~99999999
					10	0xD00C	Time of anti-Collision	0~99999999
					11	0xD00E	The number of times of the arm is close in place	0~99999999
					12	0xD010	Power on time(minute)	0~99999999
					13	0xD012	Power supply power on times	0~99999999
					14	0xD014	Running status	Binary display
					15	0xD015	Fault code	0~7
					19		Number of UP arm	0-65535
					20		Number of DOWN arm	0-65535
					21		Number of STOP	0-65535
					22		Number of Loop detector	0-65535
					23		Number of Photocell	0-65535
					24		Number of Camera	0-65535
H00-21	0-3	Factory data reset	0		1:Factory data rest,2:cumulative number of times cleared 3:Accumulate the number of times to clear and restore factory settings, return to 0 after execution
H00-22	0-1	Start acceleration time constant	0		The higher the value, the slower the acceleration
H00-23	12-30	Minimal output	10		Minimum output duty cycle of UP/DOWN arm
H00-24	12-30	STOP key function setting			0:whenever you press pause, ARM stay in the current state 1:when close arm, press the STOP key to switch the arm to up command
H00-25	1-20	Reserve
H00-26	0-1	Camera count timeout(seconds)		S	0:count cleared when10 minutes time out, Not 0 is timing close arm
H00-27	0-1
H00-28	0-3	LED light output mode			0:Do not flash alternately during operation；1:Allow flashing; 2:Green light when UP arm on 45 Degree
H00-33		485 communication status control			485 communication, analog input port data
H00-34		Peak pattern	0-1		Long press remote control whether to prohibit the use of IO port; 0: No prohibition effect; 1: effective

150W DC 24V Brushless Motor Automatic Boom Barrier With Wireless Remote Control

150W DC 24V Brushless Motor Automatic Boom Barrier With Wireless Remote Control

150W DC 24V Brushless Motor Automatic Boom Barrier With Wireless Remote Control

2. Function

3.Technical parameters

150W DC 24V Brushless Motor Automatic Boom Barrier With Wireless Remote Control