High Output Feed Hammer Mill Grinder Equipment Energy Saving

High Output Feed Hammer Mill Grinder Equipment Energy Saving

1. Application and suitable scope

JFS－3000 Serial hammer mill for alcohol ferment adapts “Dripping-shape” structure and it is the latest crushing technology and manufacturing process introduced from abroad. It is suitable for crushing many materials such as maize, dried potato, bean cake, sorghum, soybean, conch and stem, which is widely used in the alcohol, grain, feedstuff, citric acid, starch and other industries.

2. Main specifications and technical parameters

Note:

1. The reference productivity in the above table is the crushing output when the crusher is with correct installation, good suction, the negative pressure under the sieve ≤ 700～1000Pa, standard high porosity sieve plate, and the moisture content ≤14％.
2. The productivity is only for model selection reference. If there is any special requirement, it can also be designed separately.

3. Main structure and working principle

1. For structure diagram and installation foundation ,please refer to Figure 1.
2. Working principle

Material is fed from the top inlet and will enter into the crushing chamber through the feeding guide mechanism. The material is struck by high speed rotating hammerer, so it is crushed by being rubbed and struck in cycles and cutting function of punching sieve. Meanwhile under the action of centrifugal force and air flow, the material of qualified granularity will pass through the sieve pore and discharge from the outlet under the base. Customer can adapt multiple auxiliary equipments to finish the work such as material collection, conveying and warehouse entry based on the specific process.

Figure 1 JFS-3000 Installation schematic diagram

4. Hoisting installation and adjustment

1.There are 4 flying rings at both sides of the crusher for hoisting. If limited by the site condition, the machine can do plane movement through steel pipe ofφ50.

2.There are 6~9 shock absorber under the base of crushing chamber. When installation, it can be put on the foundation or the rail directly. It is not necessary to use other connection for fastening. But please note that when handle and install, the shock absorber should be landed at the same time. For installation dimension, please refer to Figure 2.

3.The arrangement of hammer must be consistent with the requirement shown in the drawing. The mass difference of the hammer of relative two groups should be ≤5 g. After being used for some stage and the first angle of hammer was worn, the motor changes its direction to use the second angle of hammer for working. When the second angle was worn, change the direction of the hammer to use its third angle and then make the rotor do reversal to use its fourth angle. After all are worn out, replace new hammer.

4.When replacing hammer, the relative two groups should be replaced at the same time.

Figure 2 Structure diagram and installation foundation

5. Operation

1,Operator should be familiar with the machine’s performance, understand its structure, and learn the Operation Instruction seriously.

2,Before starting the machine, check each connection part carefully, no looseness is allowed.

3,Check whether the rotor rotation is flexible and there should be no abnormal noise.

4,Increase feed quantity gradually after no load running for 2～3 minutes.

5,Before stopping the machine, first stop feeding, discharge all the remaining material in the machine, and then it could be stopped.

6,The rotating direction of main shaft is determined by different feeding direction. The rotating direction of motor is controlled by manual direction control of guide mechanism. Before opening the door, power supply should be switched off. When the door is opened, crusher will stop and meanwhile the motor can not be started, to guarantee the safety and reliability when replacing damageable parts and doing maintenance. After maintenance is finished and the door is closed, put the handle of feed guide plate in the correct position in accordance with the needed rotation of motor.

6. Maintenance and troubleshooting

1.Maintenance

＜1＞Operate strictly in accordance with the operation methods; every shift should do the necessary inspections and cleaning work.

＜2＞After the machine’s every working time of 4000－5000 hours, the bearings should be removed and washed once.

＜3＞Do repair or replacement immediately when the components are damaged or badly worn. The rotor should be taken for dynamic balance correction after repair or replacement.

＜4＞If the down time is long, both inside and outside of the machine should be cleaned up and remove the dustiness, to prevent corrosion and the sieve pore blocking.

＜5＞For long-term storage, the machine should be placed in a ventilated and dry place, and rain-proof measures should be taken when stored in the open air.

2.Method to remove troubles

Jiangsu Wulong Machinery Co., Ltd is located in the western suburb of Changzhou—an opening-up coasted city of Jiangsu. The company owns convenient transportation, facing Shanghai-Beijing Railway, Shanghai-Nanjing Expressway and Changzhou Airport in the north, and bordered new No. 239 Provincial Freeway.

Jiangsu Wulong Machinery Co., Ltd is a director unit of China’s Brewing Industry Association Ethanol Branch and a member of China’s Separating Machinery Industry Association. The company was established in 2000 restructuring by the original Changzhou Wujin Fermentation Engineering Machinery Plant (a municipal state-owned enterprise). The original plant was built in 1969. The company has five professional manufacturing branch offices at the moment; they are complete set of ethanol equipment manufacture branch office, crushing equipment manufacture branch office, heat exchanger manufacture branch office, decanter centrifuge manufacture branch office, and belt press filter manufacture branch office. Products are well sold to over 800 companies in over 30 provinces, cities and autonomous regions; some of them are exported to over 10 countries in Europe, Africa and Southeast Asia, and are well received by customers. The company now has more than 160 staffs and workers, 28 among that are various kinds of senior or middle professional technicians. The factory occupies an area of 24,000 square meters, and having a fixed capital of more than 30million Yuan. For dozens of years, the company has built long-term technical cooperative relations with more than ten domestic scientific and research institutes. The company has passed the authentication of ISO9001 Quality System in 2000, and strictly executes the quality system standards of ISO9001. Taking the objective of “excellent products, advanced technologies, long-term services”, the company will devote to the technical development of domestic fermentation and environment protection. Sincerely welcome the exchanges and cooperation with colleagues at home and abroad.