48 Volt Forklift Battery Charger

Charging characteristics

This charger adopts Wa+Eq charging curves with programmable intelligent control and high efficiency for charging. So the battery can reach an excellent state and prolong the battery life.

Application:

This device would be applicable to recharge of lead-acid batteries which could be used in

various electric vehicle such as power pallet trucks, fork-lift truck, lift truck, electronic tour bus.

Product Catalogs:

Product Features:

1. The charge process can be controlled intelligently with a microprocesser. optimized charge performance to get a excellent charge results.
2. Wa+Equalising charge curves.
3. The temperature rising during the charge and the evaporating of the electrolyte at the end of charge can be restricted through the controlling the charge specifications,this can prolong the battery life and reduce the lost volume of water, so it can reduce the maintenance cost.
4. Intelligent, fully automatic.
5. The advance technology and excellent units guarantee the reliable quality and perfomance.
6. Self-diagnosis and display panel indicating operational conditions.
7. It can be selected to carry out normal charge or one equqlising charge after normal charge through the adjustment of the switch.
8. It can judge the polanrity reverse and open-circuit automatically then alarm.
9. High power factor and low power aberrance.
10. The voltage of the power source can be 220V,230V and 240V or 380V, 400V and 420V,10% deviation of the total power source voltage is allowed.
11. Supply frequency 50Hz, 60Hz.

Warnings:

1. The charger must be selected according to the battery type and capacity (ampere hour). The wrong matching will make the battery to release more gas, boiling even explosion. Do not charge the battery, which is in parallel connection or the battery, which is not allowable to be charged.
2. The specialist must check the matching between the battery and charger, it is must be guaranteed that the connection from the battery to the charger is always correct.
3. Please read the operating instructions before using, the precautions and operating conditions must be abided.
4. To keep all the venting holes clean to avoid over-heating. Keeping away from liquid or short circuit will happen.
5. There is high voltage in the charger, and it is very dangerous, so it is allowable to open and maintain the charger by the specialists.
6. It is forbidden to adjust and change the charger inside for safety.

Installation for the charger

1. Conditions for installation

The charger must be placed in a dry room with good ventilation. To keep all the venting holes on the charger clean for avoiding over heat. There is no corrosive and acidic gas near to the charger to avoid corrosion for the charger.

The charger should place on the ground for operation.

2. Connection to the power supply

To connect to the power supply according to the requirements stipulated in the nameplate or operating instruction

Single-phase AC220V three cables (one for L, one for N; one for PE)

To connect the input cables of charger to L, N and PE of the power supply according to the marks. The connection to the power supply must be done by the electrical engineer according to the local standards. Otherwise, the case of the charger must be grounded.

3. Connection to the battery

Connecting the positive “+” and negative “-”of the battery with the positive “+” and negative “-”of the charger’s output respectively.

LAKER AUTO PARTS CO., LIMITED is ONE-STOP-SHOP offering parts and accessories for forklifts trucks, low-speed electric vehicles, and auxiliary material handling equipment​ with a guaranteed high-performance product at the most competitive price.

Our core products are as follows,

• Lead acid Batteries for Electric forklift trucks and Electric vehicles,
• Intelligent automatic battery chargers including industrial frequency and high frequency,
• Regular black and non-marking solid tires for forklifts used at small working fields and warehouses,
• Hydraulic solid tire press machine for mounting and dismounting the solid tires,
• Mobile loading ramp and fixed dock leveler for loading the container and goods,
• Low-speed Electric vehicle with loading platform 1Ton to 3Ton for warehouse/airport/port dock material delivery.
• and various of battery accessories for application of maintenance and replacement. ​(Such as battery plates, gauntlets, connectors, battery watering systems, battery safety valves, battery vent plugs, battery cables and etc.)

At LAKER, we are dedicated to providing comprehensive, quality service from the initial quotation to final product delivery.

Our commitment to service, knowledge, and product availability has made us a One-Stop-Shop for our customers and their business needs.

All the Forklift relevant products are selected from top-class manufacturers under their own brand MYING and LAKER, supported by skilled technicians on standby for any technical query online or solution after-market.

LAKER sincerely hopes to be your best choice for the power solution and maintenance of the Forklift!