CO2 Liquid Steam Brass Solenoid Valve Normally Closed High / Low Temperature

CO2 Liquid Steam Brass Solenoid Valve Normally Closed High / Low Temperature

Applicability

1 . The pipeline fluid must same as solenoid valve marked medium .

2 . Fluid temperature must be less than the marked temperature .

3 . If fluid is not high cleanliness , should be installed a filters in front of the solenoid valve , general solenoid valve is better claim to medium cleanness

4 . Pay attention to the orifice and port size ; usually only open and close two type ; Conditions permit , please install bypass pipe , easy maintenance ; When there is water drain to customize solenoid valve opening and closing time regulation .

5 . Pay attention to the environmental temperature on the influence of solenoid valve .

Reliability

Solenoid valve is divided into normally closed and normally open . General choose normally close , power on is open and power off is shut down ; But in the open for a long time and very short close time to choose the normally open type .

Security

1 . General solenoid valve is not waterproof , when needs waterproof model , we can be customized .

2 . Nominal pressure solenoid valve of the highest calibration must be more than the highest pressure in the pipeline , otherwise life will shorten or other unexpected circumstances .

Economy

There are a lot of solenoid valve can be common use , but on the basis of can satisfy the above three terms , should choose the most economical products.

B Series solenoid valve it is serialized products , large flow rate , good applicability . widely used in steam , oi and the other high & low temperqture linquid control

Adopted high temperature resistance seal material - PTFE ( which material import ) , when the meida passage the properties is good .

Coils type : high temperature resistance coil meanwile has the heat conduction protection .

Ensure the long life time and high reliability .

Main Technical Parameters

1 . 2 / 2 - Way solenoid valve , closed when de - energized , open when energized .

2 . Main material : body : forged brass , component : Stainless Steel

3 . Seal material : PTFE

4 . Ambient temp . : - 20 ~ 65 ℃

5 . Operating pressure : 0 . 0 ~ 50 . 0 kgf / cm ²

6 . Media temp . : - 100 ℃ ~ - 10 ℃ high temp . : 99 ℃ ~ 200 ℃

7 . Media : high temperature : steam , heat conducting oil and so on low temperature : n₂ , o₂ , co₂

attenation : under the naturature temperature , such as air , water and the other

media , please choose the other economy & suitable solenoid valve .

8 . Voltage : AC24V / 110V / 240V / 230V 50 / 60 HZ DC 12V / 24V

power consumption : AC27va ( 16 W ) DC 24W

Voltage tolerance : - 10 % ~ + 10 %

Coils type : w ( normally ) a = din standard , metallic housing

Safty series : class h heat resistance coil , ip 65

9 . Install : flow as the arrow , solenoid vertical and upright direction . if media has the eranule impurity , please install more than 60 mesh filter .

Large Diameter

Main Technical Parameters

1 . 2 / 2 - Way solenoid valve , Closed when de - energized , open when energized .

2 . Main material : body : forged brass component : stainless steel

3 . Seal Material : PTFE

4 . Ambiet Temp . : - 20 ~ 65 ℃

5 . Operating Pressure : 1 . 0 ~ 10 . 0 kgf / cm ² Max . : 15 . 0 kgf / cm ²

6 . Media Temp . : Low Temp . : - 100 ℃ ~ - 10 ℃ high Temp . : 99 ℃ ~ 185 ℃

7 . Media : high temperature steam , heat conducting oil and so on low temperature : N_{2 ,} O_{2 ,} CO₂

Attenation : Under the naturature temperature , such as air , water and the other media , please choose the other economy & suitable solenoid valve .

8 . Voltage : AC24V / 110V / 240V / 230V / 50 / 60 HZ DC12V / 24V

Power Consumption : AC27VA ( 16W ) DC24W

Voltage Tolerance : - 10 % ~ + 10 %

Coil type : W ( Normal ) = Leed Wires A = DIN Standard , Metallic Housing

Safty Series : Class H Heat resistance coil , IP 65

9 . Install : Flow as the arrow , solenoid , vertical and upright direction . if media has the granule impurity , please install more than 60 mesh filter .

FAQ

Q: How much is our minimum order quantity ?
A: Our minimun quantity is 1 Piece .

Q: Could you offer the free samples ?
A: Yeah, we could offer the free samples based on special customer.pre-production sample,production sample.

Q: What ' s your business scope ?
A: Our business scope is SMC type high quality cylinder , air source treatment , solenoid valve ,water valve,steam valve, mechnical valve ,foot valve,angle seat valve,anti-explosion valve,pluse vlave, pneumatic valve ,hydraulic ball valve,hydraulic ss ball valve,hydraulic check valve,hydraulic solenoid valve ,all type of coil,lubrication pump and parts,SS316 fitting,quick coupler , etc .

Q: What ' s your delivery date ?
A: It depends on the number of orders . Delivery date is 7 - 30 days .if small order,pls buy from our aliexpress shop, If you need emergency products , we can speed up the production of the first arrangement .

Q: What is the price of the product ?
A: Our prices are based on the size and type of material , if you can give me the information ,
then we can give you an estimated price is for reference only . We can do any size and any desgin .

Q: what types of products you can make ?
A: We can make many kinds of stainless steel materials and brass,aluminum . Valve / solenoid valve / electric valve / pneumatic valve and air cylinder products and so on .

Q: Do your company have specialized technical personnel ?
A: Design as your requirements,and have QC for make 100% inspection

Q: Can the product be made with our logo and brand ?
A: Yes , of course , we can make . we are OEM supplier for years and professional to make . But you need give us the authorization for work.

Why choose us

1: Various style for each products and completely series pneumatic products .
2: Large stock for fast shipping .
3: High quality with competitive price .
4: Sample order & small quantity order is acceptable .
5: Customize according to your special request .
6: Provide free products information .
7: Reliable quality assured and active after-sell service
8: One year quality guarantee

NINGBO SANMIN IMPORT & EXPORT CO.,LTD. was established in 2014.Our company is mainly engaged in instrumentation, pneumatic and hydraulic industry accessories and services, has more than 10 series of core products.Focusing on the production of automatic machinery to provide a variety of options, products have a wide range of applications.

Sanmin is an industrial and trade enterprise, has a strict quality control system from material selection, inspection workshop, product testing, production, inspection, packaging design to shipment.At present, the company's trade scale is expanding day by day, the customers spreads over more than 20 countries.

We are strictly abides by Chinese laws and regulations, and has won the trust of customers at home and abroad with good reputation. Welcome to telephone and send E-mail to communication, sincerely cooperate, and seek common development.

Supply Original FESTO,SMC,CKD,NORGEN,MARSH,BELLOFRAM,BELGAS,MUELLER,SBFEC.

NINGBO SANMIN IMPORT AND EXPORT CO.,LTD.

INA CHEN

Whatsapp/wechat: +86 15168536055

Skype: fhtrust

INA@PNEUHYDR.COM