Servo Motor Smart Parking Barrier 180 Degreen Folding Arm with Remote Control

Specifications:

Barrier Advanced Functions:

1. Gate automatically open when power off, no clutch design, no need human intervention. When power on,

gate automatically reset, restore to the gate closing state, truly unattended, fire safety standards. If special

requirement, manual operation is required when power off, operating arm open and close manually also can

be realized by setting up control board DIP switch, which ensure that the system can be used at any time.

2. The use of Single Compression Balance Spring device, good regulation, no noise, indefatigable, not easy

to break, safe and reliable.

3. A variety of input and output modes can be selected, normally open normally closed are optional.

4. Arm opening angle can be adjusted from 60 to 90 degrees, 10 degrees resolution, suitable for eaves

prominent place to install.

5. Closing speed can be adjusted.

6. Barrier gate up &down signal relay switch output.

7. Barrier gate running state: OK signal output indicating that the gate is working properly.

8. Barrier gate operation abnormal alarm signal output.

9. R&G Traffic light relay switch signal output.

10. External loop detector signal anti-smashing interface, infrared sensor signal anti-smashing interface.

11. Count mode interface.

12. Arm Open priority anti-smashing function. No matter the current gate in what state, the operator through the

triple push button, software or remote control to issue an open command, the gate will give priority to the

implementation of the opening action.

13. Barrier with anti-collision protection function, when the vehicle hits the gate arm, arm can be swing out to

avoid damage to the vehicle, and barrier gate machine.

14. Delay closed selection function.

15. High-sensitivity arm auto reverse function (intensity can be adjusted).

16. Parking system interface.

17.RS485 or RS232 network communication control up &down interface (no need to install communication module)

18. Anti-collision alarm signal interface.

19. Adjustable speed port (from 0.9s to 10 s)

20. High-strength precision cast steel, industry moving parts beyond the industry quality

DZ Controller Function Instruction:

1. NO/NC mode selection, in the dip switch 1, ON for NC, OFF for NO.

2. Self-locking when power off or gate automatically open selection. In dip switch 2, ON is for automatic opening when power off;

3. Automatic reverse or stop selection when meets external obstacle. In dip switch 3, ON is for automatic stop and OFF is for automatic reversing;

4. Auto closing speed adjustment selection, in the dip 4, 0.9s and 1.3s for option. ON is for 0.3s.

5. Delay automatic closed selection. Dip switch5,6,7,8 are for it and the delaying time is 1s,2s,3s,4s,5s,8s,10s,15s,20s,25s,30s,35s,40s,50s,60s for option.

6. The boom angle adjustment, suitable for some areas that the boom can’t reach the vertical position caused by obstacle.

Adjustable for 60°, 70°, 80° and 90°. And the dip switch is another independent one (1 2 switch).

7. Maintenance mode switch, convenient for possible repairing and adjusting.

8. RS485 interface, can connect with computer, check the barrier gate state and alarm information.

9. Parking lot open/close control signal and remote control open/close signal are separate. Arm opening have memory

function, Number of pulse arm opening, and closed after number of cars (must be equipped with a vehicle detector)

10. Emergent stop input signal function.

11. Arm swing out signal input function.

12. Alarm information output function.

13. Barrier gate OK signal output function.

14. All input ports are optoelectronic isolation, the input voltage range is DC5 ~ 24V

15. Vehicle detector signal input and infrared signal input, that is, use the output COM, NC of the loop detector

(normally the No.4 and No.11, specially related with detector, the barrier gate not respond to closing command

when the coil is not connected).The infrared detector uses the NPN type.

Packing List

Technical Support

If the operational failure can’t be handled by your technical staff, please contact our authorized service

representative or professional assistance.

Please provide the barrier gate model, product serial number, version and other information when contact us

for technical support services, which you can find in barrier gate model plate.

Why choose us:

1. Our Factory has 8 years OEM/ODM experiences in the line of barrier gate.
2. Prompt delivery time. Usually we keep stock of standard model which ensure the prompt delivery.
3. We accept OEM/ODM orders to meet the requirements of clients.
4. Trial order is acceptable. Clients can buy sample and test it before bulk order.
5. Online technical support makes it carefree to be our business partner.
6. A variety of transportation for your choice. Sea shipment, air cargo or express, depends on your demand.
7. Factory can be visited on working days. Clients are warmly welcome to visit our factory.