Industrial Custom Wire Drawing Machine 22KW Main Motor Low Power Consumption

HXE-22DT Small wire drawing machine with Annealer & large spool

I. Application

HXE-22DT Small wire drawing machine with annealer is used to draw and anneal single bare copper wire from 0.8mm-1.8mm to 0.3mm-1.0mm.

II. Main Technical parameters

1. Usage single bare copper wire drawing and annealing

2. Inlet size 0.8mm-1.8mm

3. Outlet size 0.3mm-1.0mm (Elongation of annealed wire 25% to 32%)

4. Machine speed/max 1500m/min

5. Die number 22, Dies size 25mm×8-10mmT, Slip ratio 15%+8%

6. Wire drawing mode standing-mode and 4axes

7. Drive by Inverter control, Brand Inovance, Most widely used brand in drawing machine

8. Main motor 22KW, Spooler motor 15KW, China best brand

9. Annealing voltage DC60V/max, Annealing current DC1000A/max, Annealing power 60KVA

10. Annealing method DC Three section annealing

11. Annealing protection will be done by steam protection

12. Capacity of compressed air 0.4-0.6Mpa, 20L/min

13. Demand Water quantity for annealing and coolant 200L/min

14. Machine frame welded by steel plate

15. Transmission Flat belts

16. Capstan Ceramic plasma

17. Lubricating system Pipe Spray

18. Bobbin size 300mm, loading capacity: 50kg/max

19. Bobbin loading & unloading type shaft type

20. Traversing unit 110W synchros motor, width: 270mm/max

21. Tension control by Air pressure tension control (With Weight balance as Backup)

22. Cabinet 0.8m*0.6m*2.0m

23. Machine dimension 2.3m*1.6m*1.9m; Installation Area 3.3m*1.7m+0.8*0.6m

24. Machine weight 3400KG, Cabinet weight 500KG. In total for shipping around 4,000KG.

III. Components

IV. Operating procedures

4-1. Open power switch

4-2. According to the wire diameter, choose the dies (Check the die list).

4-3. Use pliers to break the wire to get a smaller section.

4-4. Use pliers to make the wire through the dies, then pull the wire out (Use foot switch to make the machine running in a low speed to make the wire move).

4-5. Wire direction, please check the Drawing for Wire path.

4-6. After make the wire through all the parts, close the annealing door and the spooling door, make the tension swing arm in the lowest position. and in running, the balance arm should be in the horizontal line. No big shake, no up and down frequently.

4-7. Open the Annealing switch, open the Pump, open and adjust the Drawing lubrication oil, Cooling water, Steam, Compressed air.

4-8. Set the length meters, then press the Start button to start the machine.

V. Advantage and after-sale service

A: Advantage

(1). HENGXIE has some world famous parts suppliers, has special lubrication system for the gears and bearing.

(2). Body and other key components and parts are produced by our own factory , quality is reliable.

(3). Our company’s developing process in more than 10 years.

(4). DC. three-section annealing

B: After-self service

Our company for all machine product, since the shipment date, our company free after sale maintenance service guarantee period is:

(1) 1 year for mechanical part.

(2) 6 month for electrical part.

Under these situation mentioned, the Seller will not take responsibility, but if the Buyer agree, will charge fees accordingly to repair the machine.

A. Due to wrong operation while shipping.

B. Due to Buyer`s wrong preparation that may cause damage to the machine.

C. Due to Buyer`s wrong operation that may cause damage to the machine.

D. Not in the consuming part list.

E. After agreement are made for the shipping, for any damage, Buyer should inform Seller in letter form to repair in seven days, If beyond the dare, Seller shall take no responsibility.

F. For any other failures due to acts of God (such as lightning, typhoon, earthquake, riots, war, fire or flood) and other factors that will cause damage, Seller shall take no responsibility.

G. Seller guarantee provide long term support regarding the parts and teach. After warranty, will charge accordingly.

Suzhou Hengxie Machinery Co., Ltd was established in 2005, a total professional in drawing machine field, specialized in copper and aluminium wire drawing machines. Located in Suzhou City, very close to Shanghai, we share a convenient transportation and the most successful working environment.

Our 6,700 square meters of land allows producing a wide range of equipment, developing and researching new products. We always strive to introduce the latest international techniques to update our products.

With management concept of “Excellent quality, Reasonable prices, Superior services”, our hope is to not only meet our customers` expectations but to exceed them.

Here are the machines we have: Copper&Aluminium Rod Breakdown machine, Large and intermediate wire drawing machine with online annealer, Intermediate wire drawing machine, Intermediate wire drawing machine with online annealer, Fine wire drawing machine, Fine wire drawing machine with online annealer, Customized fine wire drawing machine with annealer, Super fine wire drawing machine. As long as we talk, we can always meet your detail requirements.

Our market includes both domestic and overseas. Such as Bangladesh, Egypt, Iran, Malaysia, Syria, Algeria, Kenya, Turkey, South Africa, Latin America and so on.

With the concept of “Stable quality and mutual development”, Hengxie welcome all customers from the world to create a sincere cooperation and win-win benefit in the future.