Add to Cart
Led Digital Packaging Drop Test Machine Electric Widening Arms Drop
Test Machine
Electric widening double-arm drop test machine JD-6001B
First, the product uses:
The double-arm drop tester is mainly used to assess the degree of
impact of the package on the actual transportation, loading and
unloading process, and to assess the impact strength and packaging
design of the package during the handling process. The drop test
machine uses the brake motor through the chain. The transmission
drives the drop arm to extend and descend. The drop height is
adopted in the digital height scale. The drop height is accurate,
the display is intuitive, the operation is simple, the drop arm is
lifted smoothly, and the drop angle error is small. This machine is
suitable for various manufacturers and quality inspection
departments.
Second, meet the design criteria:
The falling test of the two arms meets the national standards of
GB4757.5-84 JISZ0202-87 ISO2248-1972(E).
Third, the test principle:
The test sample is lifted to a predetermined height, and then it is
freely dropped in a predetermined state to collide with the impact
table. After the product is packaged, it is damaged by the fall,
and the impact strength of the electronic component is evaluated
when it is moved. The angle and surface of the packaging container
can be tested;
Fourth, the main technical parameters:
1. Drop height: 200-1200MM
2, the maximum weight of the test piece: 150Kg; electric drop
3. Height display mode: LED digital
4. Drop floor thickness: 20mm
5. Drop method: electric
6. Reset method: manual
7. Sample clamping method: diamond, angle, surface (all-round drop)
8. Arm size; 1600*400mm
9, the largest size of the test piece: 3200 * 800 * 500mm;
10, the size of the bottom plate: 3500 * 1200 * 20mm
11, motor power: 1.5kw
12, the arms are electrically adjusted width, arms moving distance;
700-3200
13. Test bench dimensions: 3500*1200*1800mm
14, drop error: ± 10mm;
15, drop plane error <1°
16, height display using high precision encoder induction
17. Control box: Separate vertical control box with anti-static
powder paint.
18. Net weight: 1800kg
19, power supply: 380V, 1.5KW
Five, equipment operation specifications
1. Turn on the power switch and the power light is on. (At this
time, it is strictly forbidden for personnel without professional
training to enter the yellow warning line to do any relevant test
operation. It is very dangerous), check whether the two wings are
in the horizontal position, otherwise the hand plate is in the
horizontal position;
2. Place the test specimen on the two wings and fix it with a
clamp; everyone stands outside the safety line.
3. Press the up button to raise the two wings to the required test
height, and press the stop button to stop the rise;
4. Press the falling key, the test item is free to fall, the test
is completed, and the sample condition after the drop test is
recorded;
5. Test the other products according to the above 2~4 test methods,
and perform the free drop test according to the required surface,
angle and edge.
6. Remarks: It is strictly forbidden to stand on the workbench
during the drop test! (Danger)
Sixth, matters needing attention and maintenance
1. The test machine casing must be grounded reliably, otherwise
there is danger of electric shock;
2. The power inlet end should be connected with air switch and
contactor with leakage protection above the same capacity, so that
the power can be cut off immediately in case of emergency;
3. When the machine is running, do not touch the part other than
the control panel with your hand to prevent scratches or crushing;
4. If you need to move the machine, be sure to cool it for 5
minutes after turning off the power.
5. After the new machine is installed in the factory, it is
necessary to add appropriate low-concentration oil to the sliding
round rod. It is strictly forbidden to add anti-rust oil or
high-concentration oil and backlog with corrosive oil.
6. If there is too much dust in the oiling station for a long time,
please lower the machine to the lower part, wipe the previous oil
and re-oil it; regularly add lubricating oil to the transmission
parts of the machine;
7. The drop machine is an impact mechanical device. When the new
machine is used more than 500 times, each screw must be tightened
to avoid malfunction.
Seven, machine studio environment requirements
Temperature: 5 ° C ~ +28 ° C [1] (average temperature within 24
hours ≤ 28 ° C)
Relative humidity: ≤85% RH
Power supply conditions Three-phase four-wire + protective ground
wire,
Voltage range: AC (380 ± 38) V