High Sensitivity Arm Parking Barrier Gate With Anti - Collision Alarm Signal Interface

24V DC Motor Servo Barrier Parking Barrier Gate For Automatic Car Parking System

Functions and Features:

1. The gate automatically open when the power is off, no clutch design, no need human intervention.
When the power is on, the gate automatically reset, and the gate returns to being closed, truly unattended,
fire safety standards. If there is special need, manual operation is required when the power is off, the
operating arm can open and close manually. Can also set up the control board DIP switch, which will
ensure the system can be used at any time
2. The use of Single Compression Balance Spring device, good regulation, no noise, indefatigable,
not easily broken, safe and reliable.
3. A variety of input and output modes can be selected, normally open normally closed are optional.
4. Arm opening angle can be adjusted from 60 to 90 degrees, 10 degrees resolution, suitable for eaves
prominent place to install.
5. Speed can be adjusted.
6. Barrier gate up &down signal relay switch output.
7. Barrier gate running state: OK signal output indicating that the gate is working properly.
8. Barrier gate operation abnormal alarm signal output.
9. R&G Traffic light relay switch signal output.
10. External loop detector signal anti-smashing interface, infrared sensor signal anti-smashing interface.
11. Count mode interface.
12. Arm Open priority anti-smashing function. No matter the current gate in what state, the operator through
the triple push button, software or remote control to issue an open command, the gate will give priority to the
implementation of the opening action.
13. Barrier with anti-collision protection function, when the vehicle hits the gate arm, arm can be swing out to
avoid damage to the vehicle and the barrier gate.
14. Delay closed selection function.
15. High-sensitivity arm auto reverse function (intensity can be adjusted).
16. Parking system interface.
17.RS485 or RS232 network communication control up &down interface (no need to install communication module)
18. Anti-collision alarm signal interface.
19. Adjustable speed port (from 0.9s to 10 s)
20. High-strength precision cast steel, industry moving parts beyond the industry quality


Adjust the Position of Barrier Arm
To adjust the position of the boom (for example, after exerting excessive force), please take the steps as below:

• open the barrier gate door and remove the cover
• loosen the two fasten screws of the DZ-1 on the boom shaft with the M12's Allen wrench, so that the
• boom can be repositioned by hand.
• adjust the position of the boom (horizontal position, as shown in picture 1).
• Use the torque wrench to tighten the two fastening screws (72 Nm)

Appendix

• Up/Down Speed Parameter Adjustments Instruction

Parameter Name Explanation:
D00spa name
PA__00 parameter item
PA__AST: reset
** _ Err: false alarm
Key Description:
Menu: menu key, switch in four parameters
L / R Arrow: Left and right movement keys, moves circularly, the corresponding characters flash
UP arrow: increase from 0 to 9, cycle key, add one for each pressing
ENTER: Enter key. Press ENTER at the currently displayed parameter to enter the specific parameter setting.
Parameter Explanation:
1d0000, 2d0000, 3d0000, 4d0000: Indicates that the current parameter is 0000, which can correspondingly
revise from the first to the fourth bit on the rightmost side.
Halfway return time parameters: PA__09 (range from 100 ~ 1500)
Up parameters: PA__10, PA__11 (range from 100 ~ 9999), PA__12 (range from 01 ~ 99),
Down parameters: PA__13, PA__14 (range from 100 ~ 9999), PA__15 (range from 01 ~ 99),
Down position parameters: PA__20 (range from 01 ~ 9999)
Up position parameter: PA__21 (range from 01 to 9999)
Resistance sensitivity: PA__23 (range from 10 to 99)
Boom level: PA__30 (range from 0 to 1)

FAQ: