Controlled By PLC X - Ray Pipeline Crawlers 250Kv 17Ah Ndtpipeline
Crawler X-Ray Machine
The basic principle of X-ray pipeline tractor mainly includes
mechanical walking part, ray generation part, positioning sensor,
logic controller, remote power supply and command source, and
positioning outside the pipeline. It is an automatic ray generating
device. The mechanical walking part drives the ray generating
device to move in the pipeline, and the special X-ray film and
label are pasted on the pipe butt weld. Note that through the
cooperation of the remote control device outside the pipeline,
positioning and exposure can be carried out in the pipeline, so as
to carry out X-ray transmission of the pipeline butt girth weld and
realize the non-destructive detection of the pipeline butt girth
weld. In addition, the forward, backward, rest and other actions of
the tractor can also be controlled by the remote control. Dust
control.
The pipeline crawler system consists of walking mechanism, visual
inspection device for observing and detecting the inner wall of the
pipe, control and communication device, etc., and repair device for
defects in the pipe can be added if necessary. According to
different application occasions, the robot can be applied to pipe
diameter of 80mm-120mm, 120mm-200mm or larger; The minimum size of
tube defect detection is 0.5×0.5mm. The robot uses dc motor drive
system, the driving force is huge. Can effectively solve pipeline
problems.
The hardware design of X-ray pipeline tractor includes: mechanical
walking part, radiation generation part, positioning sensor,
controller (circuit) part, power supply part and automatic
ambulance part. Mechanical part: it is composed of electric body,
charging power body, 24V DC motor, reducer, rubber wheel, axle and
connecting accessories. The whole machine is connected by X-ray
pipeline crawler. Charging power supply car: choose 1mm thick
stainless steel plate, stamping and welding. It is required to have
certain stiffness and is not easy to deform. Install wear resistant
material wheels. The total length is determined by the volume of
the battery. Avoid increasing turning radius, increase
transportation difficulty, the time will not be too long. See
battery Cabling method. Schematic diagram of battery wiring for
X-ray machine (schematic diagram) part: Our proposed design and
interface requirements were handed over to the specialized
manufacturer of X-ray machine. Specific requirements are: DC high
voltage DC power supply, fixed tube voltage 160kV, tube current
3mA, cancel AC/DC part, change the parameters of high voltage
package, provide fault feedback signal, heat dissipation fan
automatically open, automatic delay shutdown as required, to save
power. The console should be small and integrated with the X head.
The structure adopts dustproof design. Localization sensor part:
this problem is basically solved in the gamma-ray track machine
developed successfully in 1997. In order to reduce the complexity
of design, jitter and error can be dealt with in fault-tolerant
programming. Due to the large vibration in the transportation
process, the manufacturing process is required to be higher, the
parts are strictly screened, and anti-vibration measures are taken.
The X-ray pipeline crawlers include the special part that can
detect the welding line of long pipeline. The X-ray pipeline
crawlers have the advantages of high radiographic quality, high
imaging sensitivity, low failure rate and high work efficiency. The
X-ray pipeline crawlers have differential driving and vibration
absorbers. The chassis of the X-ray pipeline crawlers can be moved
in the pipeline steadily without off center running and
overturning. The X-ray pipeline crawlers can be moved in the
pipeline with great efficiency because it is controlled by PLC with
protecting it from blocking and under voltage. The X-ray pipeline
crawler is easy to be separated into several parts and then to be
put together, so it is easy to carry. You can change the exposure
parameter and make the X-ray pipeline crawler move, stop and have
an exposure with the exterior controlling source. The X-ray
pipeline crawlers are easy to operate.
Specification of X Ray Pipeline Crawler
Model
Specification | HXPC-100A | HXPC-100B | HXPC-100C |
Pipe diameter detecting range | Φ800—Φ1500mm | Φ500—Φ1000mm | Φ273—Φ700mm |
Total weight | 140KG | 125KG | 100KG |
Crawler length | 2200mm | 2000mm | 2000mm |
Creeping speed | 15M/min | 15M/min | 15M/min |
Creeping distance | 2KM | 2KM | 2KM |
Locating error | ±5mm | ±5mm | ±5mm |
Max.output voltage | 300Kv | 250Kv | 200Kv |
Max.outout current | 3mA | 3mA | 3mA |
Climbing ability | 40° | 40° | 25° |
Radiation angle | 360°*35° | 360°*35° | 360°*35° |
Output power | 1.5KW | 1.25KW | 1KW |
Batteryenergy | 22Ah/120V | 17Ah/120V | 12Ah/120V |
Motor power | 300W | 300W | 200W |
Exposure time | 1s~1h continues adjustable | 1s~1hcontinues adjustable | 1s~1hcontinues adjustable |
Exposure voltage | 5 selection | 5 selection | 5 selection |
Operation temperature | -30°~ 70° | -30°~ 70° | -30°~ 70° |
The crawler include below parts as standard accessories:
Main vehicle
Lead acid pile: 110V(22Ah)
X-ray machine: 250KV/5mA
Remote controller (Electro magnetic induction type, no source)