Three Axis Fiber Optic Gyroscope
Brand Name:THUNDSEA
Certification:CCS
Model Number:F3X50B
Place of Origin:China
Drawtube:Binocular
Contact Now
Add to Cart
Verified Supplier
Address:
1F,Raching Bld, No.3 Seoul Rd,
Supplier`s last login times:
within 48 hours
Product Details
Company Profile
Product Details
Model F3X50B High Accury There-axis Fiber Optic Gyroscope With 0.5 °/hr Bias Drift
1. Product Introduction
1.1 Working Principle and Function
This product is an inertial angular rate sensor based on the principle of Sagnac effect, which is used to measure the angular rate movement of the carrier around the sensitive axis of this sensor. This unit takes the fiber optic coil as the angular rate sensitive unit and the closed-loop detection circuit as the basis.
Two beams from a laser are injected into the same fibre but in opposite directions. Due to the Sagnac effect, the beam travelling against the rotation experiences a slightly shorter path delay than the other beam. The resulting differential phase shift is measured through interferometry, thus translating one component of the angular velocity into a shift of the interference pattern which is measured photometrically.
Beam splitting optics launches light from a laser diode into two waves propagating in the clockwise and anticlockwise directions through a coil consisting of many turns of optical fibre. The strength of the Sagnac effect is dependent on the effective area of the closed optical path: this is not simply the geometric area of the loop but is enhanced by the number of turns in the coil.
This product is an inertial sensor composed of optical system, corresponding power supply and data processing circuit. It can provide three-axis angle increment information.
1.2 Configuration
The product is mainly composed of the following components:
a) Optical part: light source, coupler, Y modulator, fiber coil, detector;
b) Circuit part: processor board, light source board and preamplifier;
c) Structural part: body, cover, etc.
1.3 Size
Outward dimension: Φ(79.5 ± 0.1) mm × (79.5 ± 0.1) mm × (49.8 ± 0.1) mm,
Mounting size: (73.0 ± 0.1) mm ×( 73.0 ± 0.1) mm,
1.4 Weight
500g ± 30g
1.5 Performance
| Item | Remarks | |
| range (°/s) | ±500 | |
| Scale factor Non-linearity at fixed temperature (ppm) | ≤50 | |
| Scale factor repeatability at fixed temp (ppm) | ≤100 | |
| Start-up time(s) | ≤2 | |
| Standby time(s) | ≤30 | |
| Bias drift at fixed temp (10s,1σ,°/h) | ≤0.5 | |
| Bias drift repeatability (1σ,°/h) | ≤0.5 | |
| Bias drift at full temp (10s,1σ,°/h) | ≤1 | |
| Random walk(°/√h) | ≤0.1 | |
| Misalignment angle of input shaft(＇) | ≤20 | Full temperature range |
| Threshold(°/h) | ≤0.5 | |
| Resolution | ≤0.5 | |
| Bias magnetic sensitivity (°/h/GS) | ＜0.5 | |
| Bandwidth(HZ) | ≥200 | Design assurance |
| Output delay time(μs) | ≤1000 | |
| Average values of bias before, duing and after vibration (°/h) | ≤1 | |
| Bias after vibration difference from vibration before(°/h) | ≤0.3 |
1.6 Mechanical and electrical interfaces
1.6.1 Mechanical interface
Four M3 Screws of the mounting side.
1.6.2 Power Supply and Power Consumption
| Voltage | Voltage range | Ripple(RMS) | Current |
| +5V | ±5% | ≤50mV | ＞3.00A(start-up) |
| ＞1.00A(working) |
Power consumption: working status ＜5W at room temperature, ＜8W at full temp
Start-up status: ≤ 10W
1.6.3 Electrical Connection Interface
FIG 3 Definition of connector (Model J30J-25ZKP3)
| Serial number | Signal | Contact number | Remarks |
| 1 | +5V | 1,2 | Gyroscope power supply |
| 2 | GND | 3,15 | |
| 3 | TX+ | 10,22 | RS422TX |
| 4 | TX- | 11,23 | |
| 5 | TR+ | 12,24 | RS422 RX |
| 6 | TR- | 13,25 |
Three Axis Fiber Optic Gyroscope
Inquiry Cart
0